MK3720D IDT, Integrated Device Technology Inc, MK3720D Datasheet - Page 3

• Manufacturer Part Number: MK3720D
• Description: IC VCXO DTV/SET-TOP 8-SOIC
• Manufacturer: IDT, Integrated Device Technology Inc
• Type: Voltage Controlled Crystal Oscillator (VCXO)r

Specifications of MK3720D

• Pll: Yes with Bypass
• Input: Crystal
• Output: CMOS
• Number Of Circuits: 1
• Ratio - Input:output: 2:3
• Differential - Input:output: No/No
• Frequency - Max: 54MHz
• Divider/multiplier: No/No
• Voltage - Supply: 3.15 V ~ 3.45 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC
• Frequency-max: 54MHz
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

External Component Selection
The MK3720 requires a minimum number of external
components for proper operation.
Decoupling Capacitor
A decoupling capacitor of 0.01µF must be connected
between VDD (pin 2) and GND (pin 4), as close to these
pins as possible. For optimum device performance, the
decoupling capacitor should be mounted on the component
side of the PCB. Avoid the use of vias in the decoupling
circuit.
Series Termination Resistor
When the PCB trace between the clock output (CLK, pin 5)
and the load is over 1 inch, series termination should be
used. To series terminate a 50Ω trace (a commonly used
trace impedance) place a 33Ω resistor in series with the
clock line, as close to the clock output pin as possible. The
nominal impedance of the clock output is 20Ω.
Quartz Crystal
The MK3720 VCXO function consists of the external crystal
and the integrated VCXO oscillator circuit. To assure the
best system performance (frequency pull range) and
reliability, a crystal device with the recommended
parameters (shown below) must be used, and the layout
guidelines discussed in the following section shown must be
followed.
The frequency of oscillation of a quartz crystal is determined
by its “cut” and by the load capacitors connected to it. The
MK3720 incorporates on-chip variable load capacitors that
“pull” (change) the frequency of the crystal. The crystal
specified for use with the MK3720 is designed to have zero
frequency error when the total of on-chip + stray
capacitance is
14 pF.
Recommended Crystal Parameters:
See application note MAN05 for crystal information. MAN05
is available on the internet at www.icst.com/pdf/man05.pdf.
The external crystal must be connected as close to the chip
as possible and should be on the same side of the PCB as
the MK3720. There should be no via’s between the crystal
pins and the X1 and X2 device pins. There should be no
signal traces underneath or close to the crystal.
IDT™ / ICS™ 27 MHZ AND 54 MHZ 3.3 VOLT VCXO
MK3720
27 MHZ AND 54 MHZ 3.3 VOLT VCXO
3
Crystal Tuning Load Capacitors
The crystal traces should include pads for small fixed
capacitors, one between X1 and ground, and another
between X2 and ground. Stuffing of these capacitors on the
PCB is optional. The need for these capacitors is
determined at system prototype evaluation, and is
influenced by the particular crystal used (manufacture and
frequency) and by PCB layout. The typical required
capacitor value is 1 to 4 pF.
The procedure for determining the value of these capacitors
can be found in application note MAN05.
CONFIDENTIAL (DELETE IF NOT NEEDED)
MK3720
REV I 061705
VCXO