TUA 6034V Infineon Technologies, TUA 6034V Datasheet - Page 48

• Manufacturer Part Number: TUA 6034V
• Description: IC MIXER/OSC/PLL DIGITAL VQFN-48
• Manufacturer: Infineon Technologies

Specifications of TUA 6034V

• Input: *
• Output: *
• Frequency - Max: *
• Voltage - Supply: *
• Operating Temperature: *
• Mounting Type: Surface Mount
• Package / Case: 48-VFQFN
• Frequency-max: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: SP000017969; TUA6034VXT

#
1) The RF frequency range is defined by the oscillator frequency range and the intermediate frequency (IF).
2) This is the level of the RF unwanted signal (50% amplitude modulated with 1kHz) that causes a 1.1 kHz FM
3) Local oscillator FM modulation resulting from I
4) This is the level of the RF signal (100% amplitude modulated with 11.89 kHz) that causes a 750 Hz frequency
5) Channel S02 beat is the interfering product of f
6) Channel A-5 beat is the interfering product of f
7) Channel 6 beat is the interfering product of f
8) The IF output signal stays stable within the range of the f
9) N+5 -1 MHz is defined as the input level of channel N+5, at frequency 1 MHz lower, causing FM sidebands
Specification
159. AGC output voltage V
160. AGC output voltage V
161. RF voltage range to
162. AGC output voltage AGC
163. AGC output voltage AGC
164. AGC leakage
165. AGC output voltage AGC
modulation of the local oscillator and thus of the wanted signal; V
modulation analyzer with a peak to peak detector ((P
I
are not altered. The refresh interval between each data set shall be 20 ms to 1s.
deviation on the oscillator signal producing sidebands 30 dB below the level of the oscillator signal.
mechanisms are f
mechanisms are: f
30 dB below the wanted carrier.
2
C messages are sent to the tuner in such a way that the tuner is addressed but the content of the PLL registers
Parameter
switch the AGC
from active to
inactive mode
current
This value is only guaranteed in lab.
OSC
OSC
- 2 x f
- 2 x f
IF
IF
or 2 x f
Symbol
AGC
AGC
or 2 x f
AGCmax
AGCmin
SLIP
RML
RMH
LEAK
OFF
RFpix
RFpix
- f
- f
OSC
min.
OSC
RFpix
-50
3.6
3.3
3.3
RFpix
0
0
.
RFpix,
.
Limit Values
+ f
2
, f
C communication is measured at the IF output using a
IF
RFsnd
48
f
IF
+
and f
and f
typ.
3.8
3.8
3.8
+P
- f
ref
-
)/2) and a post detection filter 30 Hz - 200 kHz. The
OSC
OSC
step for a low level RF input up to 120 dBµV.
OSC
of channel S02, f
of channel 6 at 42 MHz.
of channel A-5; f
VCC-
VCC-
max.
0.25 V
or 4
or 4
wanted
4.0
0.5
2.9
0.5
0.5
50
= 100 dBµV; f
Unit Test Conditions
V
dB
V
V
nA
V
BEAT
TUA6034, TUA6036
BEAT
maximum level,
I
minimum level
AGC bit high or
AGC active
AGC bit low or
AGC inactive
AL2, AL1, AL0 =
1,1,0
0 < V
AL2, AL1, AL0 =
1,1,1
AGC is disabled
AGC
= 37.35 MHz. The possible
unwanted
= 45.5 MHz. The possible
V 2.51, 2006-01-11
= 9 µA
AGC
=
fwanted
< V
Reference
TAIFUN
CC
+ 5.5 MHz.