934056636127 NXP Semiconductors, 934056636127 Datasheet
934056636127
Specifications of 934056636127
Related parts for 934056636127
934056636127 Summary of contents
Page 1
... Philips Semiconductors PowerMOS transistor TOPFET high side switch DESCRIPTION Monolithic single channel high side protected power switch in TOPFET2 technology assembled pin plastic package. APPLICATIONS General controller for driving lamps, motors, solenoids, heaters. FEATURES Vertical power TrenchMOS Low on-state resistance CMOS logic compatible ...
Page 2
... For normal continuous operation. A higher T to protect the switch. 2 Reverse battery voltage is allowed only with external resistors to limit the input and status currents to a safe value. The connected load must limit the reverse load current. The internal ground resistor limits the reverse battery ground current. Power is dissipated and the T rating must be observed ...
Page 3
... Internal ground resistance G 1 For a high side switch, the load pin voltage goes negative with respect to ground during the turn-off of an inductive load. 2 On-state resistance is increased if the supply voltage is less than This is the continuous current drawn from the supply when the input is low and includes leakage current to the load. ...
Page 4
... Philips Semiconductors PowerMOS transistor TOPFET high side switch INPUT CHARACTERISTICS Limits are at -40˚C BG SYMBOL PARAMETER I Input current I V Input clamping voltage IG V Input turn-on threshold voltage IG(ON) V Input turn-off threshold voltage IG(OFF) V Input turn-on hysteresis IG I Input turn-on current I(ON) ...
Page 5
... Undervoltage sensor causes the device to switch off and reset. 2 Overvoltage sensor causes the device to switch off to protect its load. 3 The status will continue to indicate OT (even if the input goes low) until the device cools below the reset threshold. Refer to . PROTECTION CHARACTERISTICS May 2001 = 25 ˚ ...
Page 6
... The battery to load threshold voltage for short circuit protection is proportional to the battery supply voltage. After short circuit protection has operated, the input voltage must be toggled low for the switch to resume normal operation. 2 Measured from when the input goes high. 3 After cooling below the reset temperature the switch will resume normal operation. ...
Page 7
... Philips Semiconductors PowerMOS transistor TOPFET high side switch II I VBG IS S VSG VIG RS Fig.4. High side switch measurements schematic. (current and voltage conventions mOhm - 100 Fig.5. Typical on-state resistance f(T ); parameter V ; condition Fig.6. Typical on-state characteristics f(T ); parameter May 2001 5 VBL ...
Page 8
... Philips Semiconductors PowerMOS transistor TOPFET high side switch 100E-6 10E-6 1E-6 100E-9 10E-9 1E-9 100E-12 - Fig.10. Typical supply quiescent current f(T ); condition 100E-6 10E-6 1E-6 100E-9 10E-9 1E-9 00E-12 10E-12 - Fig.11. Typical off-state leakage current f(T ); conditions 100E-6 10E-6 1E-6 100E-9 ...
Page 9
... Philips Semiconductors PowerMOS transistor TOPFET high side switch SG(LOW) 1 0 100 Fig.16. Typical status low characteristic f(T ); conditions 3.00 2.50 2.00 1.50 1.00 - Fig.17. Typical threshold voltage characteristic f(T ); condition 7.50 7.40 7.30 7.20 7.10 7.00 6.90 6.80 6.70 6.60 6.50 ...
Page 10
... Philips Semiconductors PowerMOS transistor TOPFET high side switch - 100 Fig.22. Typical battery to ground clamping voltage f(T ); parameter - 100 Fig.23. Typical battery to load clamping voltage f(T ); parameter I ; condition -30 -25 - Fig.24. Typical negative load clamping f(V ); conditions 0V May 2001 200 mA - -20 -25 -30 ...
Page 11
... Philips Semiconductors PowerMOS transistor TOPFET high side switch V BL(TO Fig.28. Short circuit load threshold voltage f(V ); conditions -40˚C BL(TO 1nF 100pF Fig.29. Typical output capacitance f(V ); conditions MHz -50 -100 -150 -200 -20 -15 - Fig.30. Typical reverse battery characteristic f(V ); conditions May 2001 50 max ...
Page 12
... Philips Semiconductors PowerMOS transistor TOPFET high side switch MECHANICAL DATA Plastic single-ended package; heatsink mounted; 1 mounting hole; 5-lead TO-220 lead form option D L DIMENSIONS (mm are the original dimensions) b UNIT 4.5 1.39 0.85 0.7 15.8 mm 4.1 1.27 0.70 0.4 15.2 Notes 1. Terminal dimensions are uncontrolled in this zone. ...
Page 13
... Philips Semiconductors PowerMOS transistor TOPFET high side switch DEFINITIONS DATA SHEET STATUS DATA SHEET PRODUCT 1 STATUS STATUS Objective data Development Preliminary data Qualification Product data Production Limiting values Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device ...