ADL5390ACP-REEL7 Analog Devices Inc, ADL5390ACP-REEL7 Datasheet - Page 3

• Manufacturer Part Number: ADL5390ACP-REEL7
• Manufacturer: Analog Devices Inc

Specifications of ADL5390ACP-REEL7

• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Lead Free Status / RoHS Status: Not Compliant

Parameter
OVERALL FUNCTION
GAIN CONTROL INTERFACE (I and Q)
F
F
F
SPECIFICATIONS
V
common, unless otherwise noted. 66.5 Ω termination resistors before ac-coupling capacitors on INPI and INPQ. The specifications refer
to one active channel with the other channel input terminated in 50 Ω. The common-mode level for the gain control inputs is 0.5 V. A
maximum gain setpoint of 1.0 refers to a differential gain control voltage of 0.5 V.
Table 1.
RF
RF
RF
Frequency Range
Gain Control Range
Gain Scaling
Modulation Bandwidth
Second Harmonic Distortion
Third Harmonic Distortion
Step Response
Maximum Gain
Gain Conformance
Output Noise Floor
Output IP3
Output 1 dB Compression Point
Input 1 dB Compression Point
Gain Flatness
Gain Matching
Phase Matching
Input Impedance
Output Return Loss
Maximum Gain
Gain Conformance
Output Noise Floor
Output IP3
Output 1 dB Compression Point
Input 1 dB Compression Point
Gain Flatness
Gain Matching
Phase Matching
Input Impedance
Output Return Loss
Maximum Gain
Gain Conformance
S
= 70 MHz
= 140 MHz
= 380 MHz
= 5 V, T
A
= 25°C, Z
O
= 50 Ω, F
RF
= 380 MHz, single-ended source drive to INPI and INPQ, and INMI and INMQ are ac-coupled to
Conditions
Relative to maximum gain
QBBP, QBBM, IBBM, IBBP (Pins 4, 5, 14, 15)
500 mV p-p, sinusoidal baseband input single-
ended
500 mV p-p, 1 MHz, sinusoidal baseband input
differential
500 mV p-p, 1 MHz, sinusoidal baseband input
differential
For gain from −15 dB to +5 dB
For gain from +5 dB to −15 dB
Maximum gain setpoint
Over gain setpoint of 0.2 to 1.0
Maximum gain setpoint, no RF input
RF P
F
setpoint
Maximum gain setpoint
Gain setpoint = 0.1
Over any 60 MHz bandwidth
At maximum gain setpoint
At maximum gain setpoint
INPI, INMI, INMQ, INMP (Pins 20, 21, 22, 23)
RFOP, RFOM (Pins 9, 10) measured through
balun
Maximum gain setpoint
Over gain setpoint of 0.2 to 1.0
Maximum gain setpoint, no RF input
RF P
F
gain setpoint
Maximum gain setpoint
Gain setpoint = 0.1
Over any 60 MHz bandwidth
At maximum gain setpoint
At maximum gain setpoint
INPI, INMI, INMQ, INMP (Pins 20, 21, 22, 23)
RFOP, RFOM (Pins 9, 10) measured through
balun
Maximum gain setpoint
Over gain setpoint of 0.2 to 1.0
RF1
RF1
= 70 MHz, F
= 140 MHz, F
IN
IN
= −5 dBm, frequency offset = 20 MHz
= −5 dBm, frequency offset = 20 MHz
RF2
RF2
Rev. 0 | Page 3 of 24
= 72.5 MHz, maximum gain
= 142.5 MHz, maximum
Min
20
Typ
35
3.5
230
45
55
45
47
4.6
0.25
−149
−146
23
10.7
6.7
0.25
0.5
±0.25
250||1
9.7
4.5
0.25
−144
−145
24.4
11
7.1
0.25
0.5
±0.25
250||1
9.6
4.1
0.25
Max
2400
ADL5390
Unit
MHz
dB
1/V
MHz
dBc
dBc
ns
ns
dB
dB
dBm/Hz
dBm/Hz
dBm
dBm
dB
Degrees
Ohms||pF
dB
dB
dB
dBm/Hz
dBm/Hz
dBm
dBm
dBm
dB
Degrees
Ohms||pF
dB
dB
dB
dBm
dB
dB