UPD4992GS Renesas Electronics America, UPD4992GS Datasheet
UPD4992GS
Specifications of UPD4992GS
Available stocks
Related parts for UPD4992GS
UPD4992GS Summary of contents
Page 1
To our customers, Old Company Name in Catalogs and Other Documents st On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the ...
Page 2
All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm ...
Page 3
PRELIMINARY DATA SHEET The PD4992 is a CMOS integrated circuit which outputs 8-bit parallel time and calendar data in a system in which a microprocessor is employed. The PD4992 operates at 32.768 kHz and provides year, month, day of month, ...
Page 4
PIN CONFIGURATION BLOCK DIAGRAM OSC OUT ...
Page 5
ABSOLUTE MAXIMUM RATINGS (V Item Symbol Supply voltage V Input voltage range V Output pin withstand voltage V OUT Low level output current I OUT (N ch Open Drain) Operating temperature range T opt Storage temperature range T ELECTRICAL CHARACTERISTICS ...
Page 6
WRITE CYCLE TIMING WAVEFORMS 1 ADDRESS OHZ D OUT D IN WRITE CYCLE TIMING WAVEFORMS 2 ( ADDRESS OUT ...
Page 7
READ CYCLE (unless otherwise specified V Item Symbol Cycle time t RC Address access time access time t ACS RD - output delay time output delay time t OLZ RD - output ...
Page 8
PIN FUNCTION Pin symbol Pin name CS Chip select input 1 CS Chip select input 2 WR Write signal input RD Read signal input Data input/output Address input Timing ...
Page 9
REGISTER – ADDRESS CORRESPONDENCE TABLE ADDRESS HEX BIN 000B 10s second digit 1H 001B 10s minute digit 2H 010B 12/24H AM/PM 3H 011B Leap year control 4H 100B 10s day digit 5H 101B 10s month digit 6H ...
Page 10
MODE REGISTER (R/W) HEX CONTROL REGISTER Access mode b3 0 When writing 1 * When reading (Don’t care When TP enable is ...
Page 11
TIME COUNTER 1s second digit 10s seocnd digit 1s minute digit 10s minute digit 1s hour digit 10s hour digit Day of week digit Hour 24 hour mode AM 1 o’clock 01H AM 2 o’clock 02H AM 3 o’clock 03H ...
Page 12
TYPICAL INT CONTROL EXAMPLES (mode register: INT output mode) (1) Use of INT reset (example 1) T INT reset (2) Use of INT reset (example 2) T INT output INT reset (3) Use of INT stop (example 1) INT output ...
Page 13
Use of INT reset, INT stop t 1 INT output (6) Use of TP enable INT output T INT INT Clear stop reset INT stop DISABLE ENABLE PD4992 11 ...
Page 14
TP OUTPUT (mode register: TP output mode BUSY SIGNAL Internal counter 1 Hz Busy signal output The time and calendar data read out when BUSY signal is being output may not be correct. This is because, the ...
Page 15
OUTLINE DRAWING 20PIN PLASTIC DIP (300 mil NOTES 1) Each lead centerline is located within 0.25 mm (0.01 inch) of its true position (T.P.) at maximum material condition. 2) ltem "K" to ...
Page 16
PIN PLASTIC SOP (300 mil NOTE Each lead centerline is located within 0.12 mm (0.005 inch) of its true position (T.P.) at maximum material condition PD4992 detail ...
Page 17
RECOMMENDED SOLDERING CONDITIONS The following conditions (see table below) must be met when soldering this product. Please consult with our sales offices in case other soldering process is used case soldering is done under different conditions. TYPES OF ...
Page 18
No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. ...