MAX9994ETP Maxim Integrated Products, MAX9994ETP Datasheet - Page 4

• Manufacturer Part Number: MAX9994ETP
• Description: Up-Down Converters SiGe High-Linearity, 1700MHz to 2200MHz
• Manufacturer: Maxim Integrated Products

Specifications of MAX9994ETP

• Maximum Input Frequency: 2200 MHz
• Maximum Power Dissipation: 1800 mW
• Maximum Operating Frequency: 350 MHz
• Maximum Power Gain: 9.2 dB
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Package / Case: TQFN-20 EP

SiGe High-Linearity, 1400MHz to 2200MHz
Downconversion Mixer with LO Buffer/Switch
AC ELECTRICAL CHARACTERISTICS—f
( Typical Application Circuit , RF and LO ports are driven from 50Ω sources, f
f
AC ELECTRICAL CHARACTERISTICS—f
( Typical Application Circuit , RF and LO ports are driven from 50Ω sources, f
f
4
Note 3: Operation outside this range is possible, but with degraded performance of some parameters.
Note 4: Guaranteed by design and characterization.
Note 5: All limits include external component losses. Output measurements taken at IF output of the Typical Application Circuit .
Note 6: Production tested.
Note 7: Compression point characterized. It is advisable not to operate continuously the mixer RF input above +12dBm.
Note 8: Measured with external LO source noise filtered so the noise floor is -174dBm/Hz. This specification reflects the effects of all
RF
Conversion Gain
Input Third-Order Intercept Point
Input Compression Point
(Note 7)
2LO - 2RF Spurious Response
LO-to-IF Leakage
RF
Conversion Gain
Input Third-Order Intercept Point
Input Compression Point
(Note 7)
2LO - 2RF Spurious Response
LO-to-IF Leakage
= 1455MHz, f
= 1500MHz, f
_______________________________________________________________________________________
SNR degradations in the mixer, including the LO noise as defined in Application Note 2021: Specifications and
Measurement of Local Oscillator Noise in Integrated Circuit Base Station Mixers .
PARAMETER
PARAMETER
LO
LO
= 1625MHz, f
= 1650MHz, f
IF
IF
= 170MHz, T
= 150MHz, T
SYMBOL
SYMBOL
IP
IP
2 x 2
2 x 2
IIP3
IIP3
G
G
1dB
1dB
C
C
C
C
Two tones:
f
P
P
P
LOSEL = LO2
Two tones:
f
P
P
P
RF1
RF1
RF
RF
RF
RF
RF
RF
= +25°C, LO2 is selected, unless otherwise noted.) (Note 5)
= +25°C, LO1 is selected, unless otherwise noted.) (Note 5)
= -5dBm/tone
= -10dBm
= -5dBm
= -5dBm/tone
= -10dBm
= -5dBm
= 1455MHz, f
= 1500MHz, f
RF
RF
CONDITIONS
CONDITIONS
= 1455MHz, HIGH-SIDE LO INJECTION
= 1500MHz, HIGH-SIDE LO INJECTION
RF2
RF2
= 1456MHz,
= 1501MHz,
RF
RF
< f
< f
LO
LO
, V
, V
CC
CC
= +5V, P
= +5V, P
MIN
MIN
RF
RF
-30.2
-33.2
TYP
25.6
12.7
71.4
66.4
TYP
25.5
12.5
70.4
65.4
8.8
8.9
= -5dBm, P
= -5dBm, P
MAX
MAX
LO
LO
= 0dBm,
= 0dBm,
UNITS
UNITS
dBm
dBm
dBm
dBm
dBm
dBm
dBc
dBc
dB
dB