MBB02070D8450BC100 Vishay, MBB02070D8450BC100 Datasheet - Page 7

• Manufacturer Part Number: MBB02070D8450BC100
• Description: Res Thin Film 845 Ohm 0.1% 2/5W ±25ppm/°C Conformal AXL Thru-Hole Ammo Pack
• Manufacturer: Vishay
• Type: Thin Filmr

Specifications of MBB02070D8450BC100

• Resistance Value: 845 Ohm
• Power Rating: 2/5 W
• Tolerance: 0.1 %

MBA/SMA 0204, MBB/SMA 0207, MBE/SMA 0414 - Precision
Vishay Beyschlag
TESTS AND REQUIREMENTS
Essentially all tests are carried out in accordance with the
following specifications:
EN 60115-1, Generic specification (includes tests)
EN 140100, Sectional specification (includes schedule for
qualification approval)
EN 140101-806 (successor of CECC 40101-806), Detail
specification (includes schedule for conformance inspection)
Most of the components are approved in accordance with the
European CECC-system, where applicable. The Test
Procedures and Requirements table contains only the most
important tests. For the full test schedule refer to the
documents listed above. The testing also covers most of the
requirements specified by EIA/IS-703 and JIS-C-5202.
The tests are carried out in accordance with IEC 60068-2-xx
test method and under standard atmospheric conditions in
accordance with IEC 60068-1, 5.3. Climatic category
LCT/UCT/56 (rated temperature range: Lower category
www.vishay.com
78
CLAUSE
60115-1
TEST PROCEDURES AND REQUIREMENTS
4.5
4.8
IEC
METHOD
60068-2-
TEST
IEC
-
-
Current Noise A
Temperature
Resistance
coefficient
µV/V
TEST
0.01
0.1
1
100
For technical questions, contact:
Stability for product types:
1
in accordance with IEC 60195
At 20/LCT/20 °C and
Precision Thin Film Leaded Resistors
PROCEDURE
20/UCT/20 °C
1K
MBB/SMA 0207
MBA/SMA 0204
MBE/SMA 0414
-
10K
[e-mail]
100 Ω to 100 kΩ
100 Ω to 270 kΩ
100 Ω to 470 kΩ
CLASS 0.05
STABILITY
temperature, upper category temperature; damp heat,
steady state, test duration: 56 days) is valid.
Unless otherwise specified the following values apply:
Temperature: 15 °C to 35 °C
Relative humidity: 45 % to 75 %
Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar).
For testing the components are mounted on a test board in
accordance with IEC 60115-1, 4.31 unless otherwise
specified.
In the Test Procedures and Requirements table, only the
tests and requirements are listed with reference to the
relevant clauses of IEC 60115-1 and IEC 60068-2-xx test
methods. A short description of the test procedure is also
given.
100K
PERMISSIBLE CHANGE (ΔR max.)
± 25 ppm/K; ± 15 ppm/K
> 270 kΩ to 510 kΩ
1M
> 100 Ω to 221 kΩ
REQUIREMENTS
> 470 kΩ to 1 MΩ
± 0.25 %; ± 0.1 %
43 Ω to < 100 Ω;
43 Ω to < 100 Ω;
43 Ω to <100 Ω;
STABILITY
CLASS 0.1
Resistance Value R
MBE/SMA 0414
MBB/SMA 0207
MBA/SMA 0204
Ω
10M
Document Number: 28767
22 Ω to 1.5 MΩ
22 Ω to 332 kΩ
22 Ω to 1 MΩ
CLASS 0.25
Revision: 26-Jul-10
STABILITY