PCA9514AD NXP Semiconductors, PCA9514AD Datasheet - Page 6

• Manufacturer Part Number: PCA9514AD
• Description: Hot Swappable I2C Bus and SMBus Bus Buffer 8-Pin SO Tube
• Manufacturer: NXP Semiconductors

Specifications of PCA9514AD

• Package: 8SO
• Operating Temperature: -40 to 85 °C

NXP Semiconductors
PCA9513A_PCA9514A_4
Product data sheet
8.2 Connect circuitry
8.3 Maximum number of devices in series
HIGH for the bus idle time or when all pins are HIGH and a STOP condition is seen on the
SDAIN and SCLIN pins, SDAIN is connected to SDAOUT and SCLIN is connected to
SCLOUT.
A 92 A pull-up current source on SDAIN and SCLIN of the PCA9513A is activated during
the initialization state and remains active until the power is removed or the ENABLE pin is
taken LOW. When the 92 A pull-up is active it will become high-impedance any time the
pin voltage is greater than V
Once the connection circuitry is activated, the behavior of SDAIN and SDAOUT as well as
SCLIN and SCLOUT become identical with each acting as a bidirectional buffer that
isolates the input capacitance from the output bus capacitance while communicating the
logic levels. A LOW forced on either SDAIN or SDAOUT will cause the other pin to be
driven to a LOW by the part. The same is also true for the SCLn pins. Noise between
0.7V
falls below 0.7V
one pin, the other pin in the pair turns on a pull-down driver that is referenced to a small
voltage above the falling pin. The driver will pull the pin down at a slew rate determined by
the driver and the load initially, because it does not start until the first falling pin is below
0.7V
pull-down slew rate then the initial pull-down rate will continue. If the first falling pin has a
slow slew rate then the second pin will be pulled down at its initial slew rate only until it is
just above the first pin voltage then they will both continue down at the slew rate of the
first.
Once both sides are LOW they will remain LOW until all the external drivers have stopped
driving LOWs. If both sides are being driven LOW to the same value for instance, 10 mV
by external drivers, which is the case for clock stretching and is typically the case for
acknowledge, and one side external driver stops driving that pin will rise until the internal
driver pulls it down to the offset voltage. When the last external driver stops driving a
LOW, that pin will rise up and settle out just above the other pin as both rise together with
a slew rate determined by the internal slew rate control and the RC time constant. As long
as the slew rate is at least 1.25 V/ s, when the pin voltage exceeds 0.8 V for the
PCA9513A and PCA9514A, the rise time accelerators’ circuits are turned on and the
pull-down driver is turned off.
Each buffer adds about 0.1 V dynamic level offset at 25 C with the offset larger at higher
temperatures. Maximum offset voltage (V
The LOW level at the signal origination end (master) is dependent upon the load and the
only specification point is the I
although if lightly loaded the V
the level after four buffers would be 0.5 V, which is only about 0.3 V below the threshold of
the rising edge accelerator (about 0.8 V). With great care a system with four buffers may
work, but as the V
the rising edge accelerator thus introducing false clock edges. Generally it is
recommended to limit the number of buffers in series to two, and to keep the load light to
minimize the offset.
CC
CC
. The first falling pin may have a fast or slow slew rate, if it is faster than the
and V
CC
CC
is generally ignored because a falling edge is only recognized when it
OL
with a slew rate of at least 1.25 V/ s. When a falling edge is seen on
moves up from 0.1 V, noise or bounces on the line will result in firing
Rev. 04 — 18 August 2009
CC
OL
2
, otherwise it provides current to pull the pin up to V
C-bus specification of 3 mA will produce V
may be ~0.1 V. Assuming V
Hot swappable I
PCA9513A; PCA9514A
offset
) is 0.150 V with a 10 k pull-up resistor.
2
C-bus and SMBus bus buffer
OL
= 0.1 V and V
© NXP B.V. 2009. All rights reserved.
OL
< 0.4 V,
offset
= 0.1 V,
CC
6 of 26
.