E2EQ-X7D1 Omron, E2EQ-X7D1 Datasheet
E2EQ-X7D1
Specifications of E2EQ-X7D1
Related parts for E2EQ-X7D1
E2EQ-X7D1 Summary of contents
Page 1
... Sensing distance Output configuration 3 mm (0.12 in (0.28 in (0.39 in) Part number Length Straight connector 2 m (6.5 ft) Y96E-435D2 5 m (16.4 ft) Y96E-435D5 10 m (32.8 ft) Y96E-435D10 E2EQ Part number E2EQ-X3D1 E2EQ-X7D1 E2EQ-X10D1 Part number E2EQ-X3D1-M1GJ E2EQ-X7D1-M1GJ E2EQ-X10D1-M1GJ Right angle connector Y96E-43RD2 Y96E-43RD5 Y96E-43RD10 ...
Page 2
... Note: The response frequencies for DC switching are average values measured on condition that the distance between each sensing object is twice as large as the size of the standard object and the sensing distance set is half of the maximum sensing distance. 2 E2EQ-X3D1 E2EQ-X7D1 E2EQ-X3D1-M1GJ E2EQ-X7D1-M1GJ Inductive M12 M18 Shielded VDC ( VDC) ...
Page 3
... Brown 0 V Blue Load Note possible to connect the load in two ways as shown in the above diagrams. J TIMING CHART Non-sensing zone Sensing object (%) Rated sensing distance E2EQ DC DC Setting position Unstable sensing Stable sensing zone zone 100 80 0 Lit Green Indicator Not lit ...
Page 4
... Iron E2EQ-X3D1 Standard sensing 6 E2EQ-X7D1 object Standard sensingobject Iron Iron Y(mm) E2EQ-X3D1 Sensing Head E2EQ-X7D1 Sensing Head E2EQ-X10D1 Sensing Head J SENSING DISTANCE VS. SENSING OBJECT (TYPICAL) E2EQ-X3D1 t Iron Stainlesssteel Aluminum Brass Copper Side length of sensing object (mm RESIDUAL OUTPUT VOLTAGE CHARACTERISTICS (TYPICAL) E2EQ-XjD1 ...
Page 5
... E2EQ Dimensions Unit: mm (inch) J SENSOR E2EQ-X3D1 21 dia. (0.83) 17 (0.67) E2EQ-X7D1 29 dia.(1.14) 24 (0.94) E2EQ-X10D1 42 dia.(1.65) 36 (1.42) E2EQ-X3D1-M1GJ 21 dia. (0.83) 17 (0.67) 38 (1.50) 27.6 (1.09) 24 (0.94) 5 Vinyl-insulated cable, 2 conductors, 6 dia. (45/0.12 dia.) Operation indicator 4 Standard length Two, clamping nuts M12 X 1 Cable extension (through a single metal Two, toothed washers conduit): 200 m max ...
Page 6
... E2EQ E2EQ-X7D1-M1GJ 29 dia.(1.14) 24 (0.94) E2EQ-X10D1-M1GJ 42 dia.(1.65) 36 (1.42) J MOUNTING HOLE DIMENSIONS 6 47 (1.85) 32 (1.26) 29 (1.14) 6 Operation indicator 4 Two, clamping nuts M12 X 1 Two, toothed washers 56 (2.20) 41 (1.65) 38 (1.50) 10 Operation indicator Two, clamping nuts 4 M12 X 1 Two, toothed washers Models E2EQ-X3 ...
Page 7
... J MUTUAL INTERFERENCE When installing two or more E2EQ face-to-face or side-by-side, ensure that the minimum distances given in the following table are maintained. A Model E2EQ-X3D1-j E2EQ-X7D1-j E2EQ-X10D1-j J SENSING OBJECT Part B Sensing Object Material Torque The sensing distance is reduced for non-magnetic metals. The --- sensing distance for non-magnetic metal foils less than 0 ...
Page 8
... Sensors in parallel, the leakage current through the load will be 0.8 mA times n, where n is the number of Proximity Sensors connected in parallel. J DIRECT CONNECTION TO A POWER SUPPLY Never connect the Proximity Sensor directly to a power supply without a load in the circuit. will be lower than L V ≤ E2EQ DC power supply AC power supply ...
Page 9
... One East Commerce Drive Schaumburg, IL 60173 1-800-55-OMRON Cat. No. CEDSAX4A 11/01 (12/05) OMRON ON- -LINE Global - - http://www.omron.com USA - - http://www.omron.com/oei Canada - - http://www.omron.com/oci Specifications subject to change without notice. E2EQ OMRON CANADA, INC. 885 Milner Avenue Scarborough, Ontario M1B 5V8 416-286-6465 Printed in U.S.A. ...