TISP4125H3BJR Bourns Inc., TISP4125H3BJR Datasheet - Page 10

• Manufacturer Part Number: TISP4125H3BJR
• Description: Sidacs PROTECTOR - SINGLE BIDIRECTIONAL
• Manufacturer: Bourns Inc.

Specifications of TISP4125H3BJR

• Breakover Current Ibo Max: 60 A
• Rated Repetitive Off-state Voltage Vdrm: 100 V
• Off-state Leakage Current @ Vdrm Idrm: 0.005 mA
• Forward Voltage Drop: 3 V
• Mounting Style: SMD/SMT
• Package / Case: DO-214AA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

These devices are two terminal overvoltage protectors. They may be used either singly to limit the voltage between two conductors (Figure 12)
or in multiples to limit the voltage at several points in a circuit (Figure 13).
In Figure 12, protector Th1 limits the maximum voltage between the two conductors to ±V (BO) . This configuration is normally used to protect
circuits without a ground reference, such as modems. In Figure 13, protectors Th2 and Th3 limit the maximum voltage between each conduc-
tor and ground to the ±V (BO) of the individual protector. Protector Th1 limits the maximum voltage between the two conductors to its ±V (BO)
value. If the equipment being protected has all its vulnerable components connected between the conductors and ground, then protector Th1
is not required.
To verify the withstand capability and safety of the equipment, standards require that the equipment is tested with various impulse wave forms.
The table below shows some common values.
If the impulse generator current exceeds the protector’s current rating, then a series resistance can be used to reduce the current to the
protector’s rated value to prevent possible failure. The required value of series resistance for a given waveform is given by the following
calculations. First, the minimum total circuit impedance is found by dividing the impulse generator’s peak voltage by the protector’s rated
current. The impulse generator’s fictive impedance (generators peak voltage divided by peak short circuit current) is then subtracted from the
minimum total circuit impedance to give the required value of series resistance. In some cases, the equipment will require verification over a
temperature range. By using the rated waveform values from Figure 11, the appropriate series resistor value can be calculated for ambient
temperatures in the range of -40 °C to 85 °C.
ITU-T K.20/K.21
Deployment
Impulse Testing
† FCC Part 68 terminology for the waveforms produced by the ITU-T recommendation K.21 10/700 impulse generator
GR-1089-CORE
(March 1998)
FCC Part 68
Standard
I3124
TISP4xxxH3BJ Overvoltage Protector Series
Figure 12. Two Point Protection
Peak Voltage
Setting
2500
1000
1500
1500
1000
1500
1500
4000
800
V
Th1
Waveform
10/1000
Voltage
9/720 †
9/720 †
0.5/700
10/160
10/560
10/700
2/10
µs
APPLICATIONS INFORMATION
Peak Current
Value
37.5
37.5
37.5
500
100
200
100
100
25
A
Waveform
10/1000
Current
5/320 †
5/320 †
0.2/310
10/160
10/560
5/310
2/10
µs
Customers should verify actual device performance in their specific applications.
Figure 13. Multi-point Protection
25 °C Rating
TISP4xxxH3
500
100
250
160
200
200
200
200
A
Th1
Specifications are subject to change without notice.
NOVEMBER 1997 - REVISED JANUARY 2007
Resistance
Series
Th3
Th2
Ω
0
0
0
0
0
0
0