14854-000 VXI POWER, 14854-000 Datasheet - Page 2

• Manufacturer Part Number: 14854-000
• Description: CHARGER, SW MODE, 75W, 28V
• Manufacturer: VXI POWER

Specifications of 14854-000

• Battery Charger Type: Switch Mode
• Battery Technologies Supported: Lead Acid
• Supply Voltage: 260VAC
• Accessory Type: Battery Charger
• Battery Technology: Lead Acid
• Battery Type: Lead Acid
• External Depth: 96mm
• For Use With: VRLA

Ordering information:
Dimensions
DC Output Voltages
V01 Main O/P (standard)
V02 Battery Charge O/P
DC Output Current
Shared across V01 & V02
*Total available output is 75W, main output current
will be reduced where an auxillary output is fitted
Line Regulation
(full load)
Load regulation
V01 (over range 10-100%)
V02 (over range 10-100%)
Output Ripple and Noise
PSU loaded to 60W @ 230Vrms
over a bandwidth of 0 - 30MHz
Noise/Ripple (peak-peak all outputs)
Standby Operation
Overload Protection
V01 (Primary power limit)
V02 (Constant current limit)
Battery Input
Battery Fusing
Over voltage Protection
V01 Voltages exceeding
V02 Voltages exceeding
IO1
IO2
LED1
LED2
LED3
LED4
FAULT TTL SYSTEM FAULT
FAULT TTL SYSTEM FAULT (INVERTED)
Other configurations are available-consult factory for details
Volt free relays/signals/LEDs
BATTERY LOW
SYSTEM FAULT
CHARGER FAULT
BATTERY LOW
STANDBY SUPPLY FAULT
MAIN SUPPLY FAULT
Mounting configuration
P = Panel
D = Din Rail
Tracks battery voltage on standby Tracks battery voltage on standby
120-150% Max
Temperature compensated
Up to 1A (Factory Set)
13.7V -/+ 100mV
Inherant reverse protection
14.3V +/- 50mV
12V UNIT
1.5V Typical
50mV Max
5A*Total
<100mV
5A Nom.
<0.5%
T6A
Main output voltage
16V
16V
ORACLE III 75P-28SD12ST
Conditions for active signals
Main output configuration
DP = Dual Path Fusing
R = Regulated
S = Standard
Battery low
Battery reversed
Battery disconnected
AC mains failure
Charger failure
Temperature compensated
www.vxipower.com
27.4V +/- 200mV
120%-150% Max
28.6V+/- 100mV
Up to 1A (Factory Set)
Inherant reverse protection
50mV Max
1.5V Typical
24V UNIT
2.5A* Total
<0.5%
<100mV
2.5A Nom.
T4A
32V
32V
No of outputs
D = Dual (Main and Batt)
T = Triple
Q = Quad
Options
EMC
Susceptibility
Environmental
Ambient Operating Temp
Storage Temperature
Connectors
Input/Output/Signal
Thermistor
Input Voltage
Input Frequency
Input Current
Input Fusing
PCB Mounted fuse
Inrush Current
Efficiency
Spec
Output
current
Line
regulation
(full load)
Load
regulation
(10-100%)
Overcurrent
protection
Overvoltage
protection
Ripple/noise
(Full load,
pk-pk)
Auxillary output voltage(s)
main output
Regulated
2.5A/1.7A
12 or 24V
120% nom
120% nom
<0.5%
<0.5%
* consult factory for 12V dual path fusing applications
<1%
Connectors
ST = Screw Terminals
K = Klippon
-5
Screw Terminal or Weidmuller Kilppon
EN50081-1 Emissions
EN50082-2 Immunity
EN61000-4-2 ESD
EN61000-4-3 Radiated Electro Interference
EN61000-4-4 Fast Bursts
-30
0.1” Molex 2 way
90V - 260V AC rms
47 - 63Hz
2A rms typ @ 110V
1A rms typ @ 230V
T3.15AA, 250V AC HRC
UL/CSA Approved
<30A peak, cold start 20
12V UNIT
24V UNIT
o
Auxillary output
C to +40
5V, 12-15V, 24V
5V/3A, 12-15V 2A
o
C to +85
120% nom
120% nom
<1%
24V 1.25A
<0.5%
<0.5%
o
C derate 2.5% per
o
C
>75% under all conditions
>82% under all conditions
o
C ambient - 265V AC
2 x pcb 2A*fuses
(split main output)
Dual Path fusing
o
C>40
00030:Rev1
o
C