SC4518HEVB-2 Semtech, SC4518HEVB-2 Datasheet - Page 8

• Manufacturer Part Number: SC4518HEVB-2
• Description: EVALUATION BOARD
• Manufacturer: Semtech

Specifications of SC4518HEVB-2

• Silicon Manufacturer: Semtech
• Application Sub Type: Step Down Switching Regulator
• Kit Application Type: Power Management - Voltage Regulator
• Silicon Core Number: SC4518H
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Figure 2. Theoretical maximum load current curves
Inductor Selection
The factors for selecting the inductor include its cost,
efficiency, size and EMI. For a typical SC4518H
application, the inductor selection is mainly based on its
value, saturation current and DC resistance. Increasing
the inductor value will decrease the ripple level of the
output voltage while the output transient response will
be degraded. Low value inductors offer small size and
fast transient responses while they cause large ripple
currents, poor efficiencies and more output capacitance
to filter out the large ripple currents. The inductor should
be able to handle the peak current without saturating
and its copper resistance in the winding should be as low
as possible to minimize its resistive power loss. A good
trade-off among its size, loss and cost is to set the
inductor ripple current to be within 15% to 30% of the
maximum output current.
The inductor value can be determined according to its
operating point under its continuous mode and the
switching frequency as follows:
Where:
fs = switching frequency,
output load current and
V
The peak to peak inductor current is:
POWER MANAGEMENT
Application Information (Cont.)
O
I = ratio of the peak to peak inductor current to the
2007 Semtech Corp.
= output voltage.
1.900
1.880
1.860
1.840
1.820
1.800
1.780
1.760
1.740
1.720
1.700
Maximum Load Current vs Input Voltage
4
6
L
8
V
10
V
Vi (V)
I
L=10uH
O
f
s
12
(
V
I
I I
14
V
OMAX
O
)
16
18
Vo=2.5V
Vo=3.3V
Vo=5V
8
After the required inductor value is selected, the proper
selection of the core material is based on the peak
inductor current and efficiency specifications. The core
must be able to handle the peak inductor current I
without saturation and produce low core loss during the
high frequency operation.
The power loss for the inductor includes its core loss and
copper loss. If possible, the winding resistance should
be minimized to reduce inductor’s copper loss. The core
must be able to handle the peak inductor current I
without saturation and produce low core loss during the
high frequency operation. The power loss for the inductor
includes its core loss and copper loss. If possible, the
winding resistance should be minimized to reduce
inductor’s copper loss. The core loss can be found in the
manufacturer’s datasheet. The inductor’s copper loss
can be estimated as follows:
Where:
be calculated as follows:
Output Capacitor Selection
Basically there are two major factors to consider in
selecting the type and quantity of the output capacitors.
The first one is the required ESR (Equivalent Series
Resistance) which should be low enough to reduce the
output voltage deviation during load changes. The second
one is the required capacitance, which should be high
enough to hold up the output voltage. Before the
SC4518H regulates the inductor current to a new value
during a load transient, the output capacitor delivers all
the additional current needed by the load. The ESR and
ESL of the output capacitor, the loop parasitic inductance
between the output capacitor and the load combined
with inductor ripple current are all major contributors to
the output voltage ripple. Surface mount ceramic
capacitors are recommended.
I
LRMS
is the RMS current in the inductor. This current can
P
I
LRMS
COPPER
I
PEAK
I
p
I
p
OMAX
I
I
2
OMAX
LRMS
I
I
1
OMAX
R
I
p
3
1
WINDING
2
p
I
2
SC4518H
www.semtech.com
PEAK
PEAK