GP3000S30-0.125-02-4/4 Bergquist, GP3000S30-0.125-02-4/4 Datasheet
GP3000S30-0.125-02-4/4
Specifications of GP3000S30-0.125-02-4/4
Related parts for GP3000S30-0.125-02-4/4
GP3000S30-0.125-02-4/4 Summary of contents
Page 1
Introduction Thermal Properties and Testing Interface Material Selection Guide ® Gap Pad Thermally Conductive Materials Gap Pad Comparison Data Frequently Asked Questions ® Gap Pad VO ® Gap Pad VO Soft Gap Pad VO Ultra Soft Gap Pad 1000SF Gap ...
Page 2
... Bergquist Takes the Heat Thermal Management Products Bergquist's Thermal Products Group is a world- leading developer and manufacturer of thermal management materials which provide product solutions to control and manage heat in electronic assemblies and printed circuit boards. Used by many of the world’s largest ...
Page 3
... The Bergquist Company.Today, developing innovative products for the electronics industry remains our first priority. Bergquist has developed over 260 materials which provide thermal solutions for a wide variety of electronic applications. Many of our products were originally developed to satisfy ...
Page 4
... Increasing mounting pressure under ideal conditions decreases thermal impedance. Time: Thermal impedance decreases over time. Measurement: Thermal impedance is affected by the method of temperature measurement. Thermal Impedance Per Bergquist TO-220 Thermal o Performance (25 C Cold Plate Testing) 4 Thermal Resistance The opposition to the flow of heat through a unit area of material across an undefined thickness ...
Page 5
... Interface Material Selection Guide Sil-Pad A1500 T = Typical Application-Specific (contact Bergquist Sales Available Roll stock configurations are limited — contact your Bergquist Sales Representative for more information. Note: For Hi-Flow 225UT, Hi-Flow 225FT, and Hi-Flow 225F-AC, the adhesive is not a pressure sensitive adhesive (PSA). ...
Page 6
... The extensive Gap Pad family provides an effective thermal interface between heat sinks and electronic devices where uneven surface topography, air gaps and rough surface textures are present. Bergquist application specialists work closely with customers to specify the proper Gap Pad material for each unique thermal management requirement. ...
Page 7
Gap Pad ® Comparison Data Conductivity, Hardness and General Overview 7 ...
Page 8
... Is Gap Pad reworkable? A: Depending on the application and the pad being used, Gap Pad has been reworked in the past. Bergquist has customers that are currently using the same pad for reassembling their applications after burn-in processes and after fieldwork repairs. However, this is left up to the design engineer’ ...
Page 9
... Sheet form and die-cut parts Building a Part Number – – – – GPVO 0.040 AC 0816 NA Note: To build a part number, visit our website at www.bergquistcompany.com. Gap Pad ® : U.S. Patent 5,679,457 and others. Gap Pad VO METRIC VALUE TEST METHOD Gold/Pink Visual Sil-Pad — ...
Page 10
... Sheet form and die-cut parts Building a Part Number – – – – GPVOS 0.060 AC 00 ACME10256 Rev. a Note: To build a part number, visit our website at www.bergquistcompany.com. Gap Pad ® : U.S. Patent 5,679,457 and others. METRIC VALUE TEST METHOD Mauve/Pink Visual Sil-Pad — 0.508 to 5.080 ...
Page 11
... Sheet form and die-cut parts Building a Part Number – – – – GPVOUS 0.100 AC 0816 NA Note: To build a part number, visit our website at www.bergquistcompany.com. Gap Pad ® : U.S. Patent 5,679,457 and others. ® VO Ultra Soft METRIC VALUE TEST METHOD Mauve/Pink Visual Sil-Pad Sil-Pad — ...
Page 12
... Die-cut parts Building a Part Number GP1000SF – 0.010 – 02 – 0816 – Note: To build a part number, visit our website at www.bergquistcompany.com. Gap Pad ® : U.S. Patent 5,679,457 and others. METRIC VALUE TEST METHOD Green Green Visual Fiberglass Fiberglass — 0.254 to 3.175 ...
Page 13
... Sheet form, die-cut parts, and roll form (converted or unconverted) Building a Part Number – – – – HC1000 0.015 02 0816 NA Note: To build a part number, visit our website at www.bergquistcompany.com. Gap Pad ® : U.S. Patent 5,679,457 and others. ® HC1000 METRIC VALUE TEST METHOD Gray Gray Visual Fiberglass — ...
Page 14
... Sheet form and die-cut parts Building a Part Number – – – – GP1500 0.100 02 0816 NA Note: To build a part number, visit our website at www.bergquistcompany.com. Gap Pad ® : U.S. Patent 5,679,457 and others. METRIC VALUE TEST METHOD Black Black Visual — — ...
Page 15
... Sheet form, die-cut parts, and roll form (converted or unconverted) Building a Part Number – – – – GP1500R 0.020 02 00 ACME10256 Rev. A Note: To build a part number, visit our website at www.bergquistcompany.com. Gap Pad ® : U.S. Patent 5,679,457 and others. ® 1500R METRIC VALUE TEST METHOD Black Black Visual Fiberglass — ...
Page 16
... Sheet form, die-cut parts and roll form (converted or unconverted) Building a Part Number Standard Options – – – – GPA2000 0.010 02 0816 NA Note: To build a part number, visit our website at www.bergquistcompany.com. Gap Pad ® : U.S. Patent 5,679,457 and others. METRIC VALUE TEST METHOD Gray Gray Visual Fiberglass — ...
Page 17
... Sheet form and die-cut parts Building a Part Number – – – – GP2000S40 0.020 02 0816 NA Note: To build a part number, visit our website at www.bergquistcompany.com. Gap Pad ® : U.S. Patent 5,679,457 and others. ® 2000S40 METRIC VALUE TEST METHOD Gray Gray Visual Fiberglass — ...
Page 18
... Sheet form and die-cut parts Building a Part Number – – – – GP2500S20 0.100 02 00 ACME 89302 Rev a Note: To build a part number, visit our website at www.bergquistcompany.com. Gap Pad ® : U.S. Patent 5,679,457 and others. METRIC VALUE TEST METHOD Light Yellow Visual Fiberglass — 0.254 to 3.175 ...
Page 19
... Sheet form and die-cut parts Building a Part Number – – – – GP2500 0.100 02 00 ACME 89302 Rev a Note: To build a part number, visit our website at www.bergquistcompany.com. Gap Pad ® : U.S. Patent 5,679,457 and others. Gap Pad ® 2500 METRIC VALUE TEST METHOD Light Brown Visual — ...
Page 20
... Sheet form, die-cut parts and roll form (converted or unconverted) Building a Part Number – – – – GPA3000 0.015 01 0816 NA Note: To build a part number, visit our website at www.bergquistcompany.com. Gap Pad ® : U.S. Patent 5,679,457 and others. METRIC VALUE TEST METHOD Gold Gold Visual Fiberglass — ...
Page 21
... NA = Selected standard option. If not selecting a standard option, insert company name, drawing number, and revision level. 0816 = Standard sheet size 8" x 16" custom configuration 02 = Natural tack, both sides Standard thicknesses available: 0.010", 0.015", 0.020", 0.040", 0.060", 0.080", 0.100", 0.125" GP3000S30 = Gap Pad 3000S30 Material 21 ...
Page 22
... For more information on Gap Pad modulus, refer to Bergquist Application Note #116. 3) The ASTM D5470 test fix- ture was used.The recorded value includes interfacial thermal resistance.These values are provided for reference only. Actual applica- tion performance is directly related to the surface roughness, flatness and pressure applied. ...
Page 23
... For smaller quantity packaging, please contact Bergquist Sales Building a Part Number – – – – GF1000 00 15 50cc NA Note: To build a part number, visit our website at www.bergquistcompany.com. Gap Pad ® : U.S. Patent 5,679,457 and others. METRIC VALUE TEST METHOD Gray Gray Visual White Visual ...
Page 24
... Supplied in cartridge or kit form Building a Part Number – – – – GF1100SF 00 15 400cc NA Note: To build a part number, visit our website at www.bergquistcompany.com. Gap Pad ® : U.S. Patent 5,679,457 and others. METRIC VALUE TEST METHOD Yellow Visual Red Red Visual 450,000 ASTM D2196 2 ...
Page 25
... Good thermal performance: 1.4 W/mK • Stress conforming through low modulus Gap Filler Gel 1500 is the first member in Bergquist’s new family of pre-cured gap filling materials.The product is a highly conformable gel which requires no curing, mixing or refrig- eration. It’s unique formulation assures excel- ...
Page 26
... For smaller quantity packaging, please contact Bergquist Sales Building a Part Number – – – – GF2000 00 60 10G NA Note: To build a part number, visit our website at www.bergquistcompany.com. Gap Pad ® : U.S. Patent 5,679,457 and others. METRIC VALUE TEST METHOD Pink Pink Visual White Visual ...
Page 27
Gap Filler 3500S35 (Two-Part) Features and Benefits • Thermal Conductivity: 3.6 W/m-K • Thixotropic nature makes it easy to dispense • Two-part formulation for easy storage • Ultra-conforming - designed for fragile and low stress applications • Ambient or accelerated ...
Page 28
... TIC ™ - Thermal Interface Compound Thermally Conductive Grease Compounds Bergquist’s line of thermally conductive thermal interface compounds will flow under assembly pressure to wet-out the thermal interface surfaces and produce very low thermal impedance. TIC products are Features Benefits The TIC portfolio has diverse ...
Page 29
... Be sure heat sink is dry before applying TIC 1000G. Application Methods 1. Dispense and/or screenprint TIC 1000G compound onto the processor or heat sink surface like thermal grease (see a Bergquist Representative for application information). 2. Assemble the processor and heat sink with spring clips or constant-pressure fasteners. Typical Applications Include: • ...
Page 30
... Ensure heat sink is dry before applying TIC 1000A. Application Methods 1. Dispense and/or screenprint TIC 1000A compound onto the processor or heat sink surface like thermal grease (see a Bergquist Representative for application information). 2. Assemble the processor and heat sink with spring clips or constant-pressure fasteners. Typical Applications Include: • ...
Page 31
... TIC 4000. Although Bergquist estimates a 0.02 ml (cc) volumetric requirement for a 0.5" x 0.5" component interface, dispensed at a thickness of 0.005", Bergquist also recognizes that an optimized application would utilize the minimum volume of TIC 4000 material necessary to ensure complete wet-out of both mechanical interfaces. ...
Page 32
... Simplified application process • Tackified or tack-free at room temperature 32 The Hi-Flow family of phase change thermal interface materials covers a wide range of applications.The Bergquist Company is a leader in thermal management solutions and works closely with customers to ensure that the proper Hi-Flow material is specified. Options Applications ...
Page 33
Hi-Flow ® Comparison Data TO-220 Thermal Performance 33 ...
Page 34
... Hi-Flow material will not likely have to be replaced. If the material has gone through the phase change, it will adhere very well to both surfaces. In this case, Bergquist suggests warming the heat sink to soften the Hi-Flow compound for easier removal from the processor. Replace with a new piece of Hi-Flow material. ...
Page 35
... ASTM D5470. Please contact Bergquist Product Management if additional specifications are required. 2) The ASTM D5470 test fixture was used and the test sample was conditioned at 70°C prior to test.The recorded value includes interfacial thermal resistance ...
Page 36
... ASTM D5470. Please contact Bergquist Product Management if additional specifications are required. 2) The ASTM D5470 test fixture was used and the test sample was conditioned at 70°C prior to test.The recorded value includes interfacial thermal resistance ...
Page 37
... ASTM D5470. Please contact Bergquist Product Management if additional specifications are required. 2) The ASTM D5470 test fixture was used and the test sample was conditioned at 70°C prior to test.The recorded value includes interfacial thermal resistance ...
Page 38
... ASTM D5470. Please contact Bergquist Product Management if additional specifications are required. 2) The ASTM D5470 test fixture was used and the test sample was conditioned at 70°C prior to test.The recorded value includes interfacial thermal resistance ...
Page 39
... ASTM D5470. Please contact Bergquist Product Management if additional specifications are required. 2) The ASTM D5470 test fixture was used and the test sample was conditioned at 70°C prior to test.The recorded value includes interfacial thermal resistance ...
Page 40
... ASTM D5470. Please contact Bergquist Product Management if additional specifications are required. 2) The ASTM D5470 test fixture was used and the test sample was conditioned at 70°C prior to test.The recorded value includes interfacial thermal resistance ...
Page 41
... ASTM D5470. Please contact Bergquist Product Management if additional specifications are required. 2) The ASTM D5470 test fixture was used and the test sample was conditioned at 70°C prior to test.The recorded value includes interfacial thermal resistance ...
Page 42
... ASTM D5470. Please contact Bergquist Product Management if additional specifications are required. 2) The ASTM D5470 test fixture was used and the test sample was conditioned at 70°C prior to test.The recorded value includes interfacial thermal resistance ...
Page 43
... ASTM D5470. Please contact Bergquist Product Management if additional specifications are required. 2) The ASTM D5470 test fixture was used and the test sample was conditioned at 70°C prior to test.The recorded value includes interfacial thermal resistance ...
Page 44
... ASTM D5470. Please contact Bergquist Product Management if additional specifications are required. 2) The ASTM D5470 test fixture was used and the test sample was conditioned at 70°C prior to test.The recorded value includes interfacial thermal resistance ...
Page 45
... Comprehensive choices for a cleaner and more efficient thermal interface More than 25 years ago, Bergquist set the standard for elastomeric thermal interface materials with the introduction of Sil-Pad.Today, Bergquist is a world leader with a complete family of Sil-Pad materials to meet the critical needs of a rapidly changing electronics industry. Features ...
Page 46
Sil-Pad ® Comparison Data TO-220 Thermal Performance Q-Pad Materials Non-Electrically Isolating 2.75 2.50 2.25 2.00 1.75 1.50 1.25 1.00 0.75 0.50 0.25 0. 100 Interface Pressure (psi) Sil-Pad High Performance Materials 3.25 Sil-Pad 1750 Sil-Pad A1500, 10 mil ...
Page 47
... Are there differences in electrical characteristics between Sil-Pad A2000 and Sil-Pad 2000? A: Yes. Bergquist evaluates and publishes voltage breakdown, dielectric constant and volume resistivity data per ASTM standards for these materials. Due to differences between ASTM lab testing and actual application performance, for best results, these characteristics should be evaluated within the actual customer system ...
Page 48
... Why Choose Sil-Pad Thermally Conductive Insulators? Overview The Bergquist Company established the standard for elastomeric, thermally conductive insulation materials with the development of Sil-Pad over 25 years ago. Sil-Pad was developed as a clean, grease- free alternative to mica and grease. Now, a complete family of materials is available to meet the diverse and changing requirements of today’ ...
Page 49
Sil-Pad Materials Sil-Pad thermally conductive insulators are designed to be clean, grease-free and flexible.The combination of a tough carrier material such as fiberglass and silicone rubber which is conformable, provides the engineer with a more versatile material than mica or ...
Page 50
... Sil-Pad applications is resistance to cut-through to avoid electrical shorting from the device to the heat sink. Cut-Through Resistance - Bergquist introduced its TO-220 cut-through test to help customers better understand typical application performance. Mounting Techniques and Mounting Pressure Typical mounting techniques include: • ...
Page 51
... As the material is applied in different ways, the thermal impedance values will vary from application to application. • The original Sil-Pad material, Sil-Pad 400, continues to be Bergquist's most popular material for many applications. • Sil-Pad A1500 is chosen when greater thermal performance is required ...
Page 52
Sil-Pad 400 .007 in. Color Gray .007 ± .001 Thickness (in/mm) (.18 ± .025) Thermal Performance 5.14 TO-220 Test @ 50 psi °C/W Thermal Impedance (°C-in 2 /W) 1.13 Thermal Conductivity 0.9 (W/m-K nominal) Voltage Breakdown (Vac) 3500 Continuous Use ...
Page 53
... The materials comparison tool can be used for most Bergquist thermal materials, including Sil-Pad, Hi-Flow, Gap Pad, Q-Pad, Bond-Ply and Liqui-Bond products. Test Method ...
Page 54
... Sheet form, die-cut parts and roll form; with or without pressure sensitive adhesive Building a Part Number – – – – SP400 0.007 AC 12/250 NA Note: To build a part number, visit our website at www.bergquistcompany.com. Sil-Pad ® U.S. Patents 4,574,879; 4,602,125; 4,602,678; 4,685,987; 4,842,911 and others METRIC VALUE TEST METHOD Gray Gray Visual Fiberglass — ...
Page 55
... With or without pressure sensitive adhesive Building a Part Number – – – – SP800 0.005 AC 1212 NA Note: To build a part number, visit our website at www.bergquistcompany.com. Sil-Pad ® : U.S. Patents 4,574,879; 4,602,125; 4,602,678; 4,685,987; 4,842,911 and others Sil-Pad ® 800 METRIC VALUE TEST METHOD Gold Gold ...
Page 56
... Building a Part Number – – – – SP900S 0.009 AC 00 ACME 951753 Rev B Note: To build a part number, visit our website at www.bergquistcompany.com. Sil-Pad ® : U.S. Patents 4,574,879; 4,602,125; 4,602,678; 4,685,987; 4,842,911 and others METRIC VALUE TEST METHOD Pink Pink Visual Fiberglass — ...
Page 57
... Building a Part Number – – – – SP980 0.009 AC 00 ACME 951753 Rev B Note: To build a part number, visit our website at www.bergquistcompany.com. Sil-Pad ® : U.S. Patents 4,574,879; 4,602,125; 4,602,678; 4,685,987; 4,842,911 and others Sil-Pad ® 980 METRIC VALUE TEST METHOD Mauve Visual Fiberglass — ...
Page 58
... Fiberglass reinforced • Valve alternative to Sil-Pad 1500ST Sil-Pad 1100ST (Soft Tack fiberglass- reinforced thermal interface material featuring inherent tack on both sides.The material exhibits excellent thermal performance at low mounting pressures.The material is sup- plied on two liners for exceptionally easy handling prior to auto-placement in high-vol- ume assemblies ...
Page 59
... With or without pressure sensitive adhesive Building a Part Number – – – – SPA1500 0.010 AC 12/250 NA Note: To build a part number, visit our website at www.bergquistcompany.com. Sil-Pad ® : U.S. Patents 4,574,879; 4,602,125; 4,602,678; 4,685,987; 4,842,911 and others Sil-Pad ® A1500 METRIC VALUE TEST METHOD Green Visual Fiberglass — ...
Page 60
... Also available in 12 mil thickness Building a Part Number SP1500ST – 0.008 – 02 – 1012 – NA Note: To build a part number, visit our website at www.bergquistcompany.com. Sil-Pad ® : U.S. Patents 4,574,879; 4,602,125; 4,602,678; 4,685,987; 4,842,911 and others METRIC VALUE TEST METHOD Blue Blue Visual Fiberglass — ...
Page 61
... With or without pressure sensitive adhesive Building a Part Number – – – – SP1750 0.012 AC 1212 NA Note: To build a part number, visit our website at www.bergquistcompany.com. Sil-Pad ® : U.S. Patents 4,574,879; 4,602,125; 4,602,678; 4,685,987; 4,842,911 and others Sil-Pad ® 1750 METRIC VALUE TEST METHOD Green Visual Fiberglass — ...
Page 62
... With or without pressure sensitive adhesive – – – – SP2000 0.010 Note: To build a part number, visit our website at www.bergquistcompany.com. Building a Part Number Sil-Pad ® : U.S. Patents 4,574,879; 4,602,125; 4,602,678; 4,685,987; 4,842,911 and others METRIC VALUE TEST METHOD White Visual Fiberglass — ...
Page 63
... With or without pressure sensitive adhesive Building a Part Number – – – – SPA2000 0.015 00 1012 NA Note: To build a part number, visit our website at www.bergquistcompany.com. Sil-Pad ® : U.S. Patents 4,574,879; 4,602,125; 4,602,678; 4,685,987; 4,842,911 and others Sil-Pad ® A2000 METRIC VALUE TEST METHOD White Visual Fiberglass — ...
Page 64
... With or without pressure sensitive adhesive Building a Part Number – – – – SPK4 0.006 00 12/250 NA Note: To build a part number, visit our website at www.bergquistcompany.com. Sil-Pad ® : U.S. Patents 4,574,879; 4,602,125; 4,602,678; 4,685,987; 4,842,911 and others. Kapton ® registered trademark of DuPont. METRIC VALUE TEST METHOD Gray Gray ...
Page 65
... With or without pressure sensitive adhesive Building a Part Number – – – – SPK6 0.006 AC 12/250 NA Note: To build a part number, visit our website at www.bergquistcompany.com. Sil-Pad ® : U.S. Patents 4,574,879; 4,602,125; 4,602,678; 4,685,987; 4,842,911 and others Kapton ® registered trademark of DuPont. Sil-Pad ® K-6 ® ...
Page 66
... With or without pressure sensitive adhesive Building a Part Number – – – – SPK10 0.006 AC 1212 NA Note: To build a part number, visit our website at www.bergquistcompany.com. Sil-Pad ® : U.S. Patents 4,574,879; 4,602,125; 4,602,678; 4,685,987; 4,842,911 and others. Kapton ® registered trademark of DuPont. METRIC VALUE TEST METHOD Beige Visual Kapton — ...
Page 67
... Sil-Pad rubber.The material is designed for those applications in which maxi- mum heat transfer is needed and electrical isolation is not required. Q-Pad II is the ideal thermal interface material to replace messy thermal grease compounds. Q-Pad II eliminates problems associated with grease such as contamination of reflow solder or cleaning operations ...
Page 68
... With or without pressure sensitive adhesive Building a Part Number Q3 – 0.005 – AC – 12/250 – NA Note: To build a part number, visit our website at www.bergquistcompany.com. Sil-Pad ® : U.S. Patents 4,574,879; 4,602,125; 4,602,678; 4,685,987; 4,842,911 and others METRIC VALUE TEST METHOD Black Black Visual Fiberglass — ...
Page 69
... Building a Part Number – – – – PP400 0.009 00 1212 NA Note: To build a part number, visit our website at www.bergquistcompany.com. Sil-Pad ® : U.S. Patents 4,574,879; 4,602,125; 4,602,678; 4,685,987; 4,842,911 and others Poly-Pad ® 400 METRIC VALUE TEST METHOD Tan Visual Fiberglass — ...
Page 70
... With or without pressure sensitive adhesive Building a Part Number PP1000 – 0.009 – 00 – 1212 – NA Note: To build a part number, visit our website at www.bergquistcompany.com. Sil-Pad ® : U.S. Patents 4,574,879; 4,602,125; 4,602,678; 4,685,987; 4,842,911 and others METRIC VALUE TEST METHOD Yellow Visual Fiberglass — 0.229 ...
Page 71
... With or without pressure sensitive adhesive Building a Part Number PPK4 – 0.006 – 00 – 12/250 – NA Note: To build a part number, visit our website at www.bergquistcompany.com. Sil-Pad ® : U.S. Patents 4,574,879; 4,602,125; 4,602,678; 4,685,987; 4,842,911 and others Kapton ® registered trademark of DuPont. Poly-Pad ® K-4 METRIC VALUE ...
Page 72
... With or without pressure sensitive adhesive Building a Part Number PPK10 – 0.006 – AC – 1212 – NA Note: To build a part number, visit our website at www.bergquistcompany.com. Sil-Pad ® : U.S. Patents 4,574,879; 4,602,125; 4,602,678; 4,685,987; 4,842,911 and others Kapton ® registered trademark of DuPont. METRIC VALUE TEST METHOD Yellow Visual Kapton — ...
Page 73
... B = Inner Diameter (.433") or 13.5 mm (.532") ± 1.0 mm (± .039" Length (.985" (1.18") +3. -0 .125" 0.0") Special lengths are available. For more information, contact a Bergquist Sales Representative. Ordering Procedure: Sample: SPT 400 ___ - ___ - ___ “A” – “B” – “C” ...
Page 74
Sil-Pad ® Shield Bonded Laminate of Sil-Pad with a Copper Shield Features and Benefits • Bonded laminate • Electrically isolating • Copper shield between layers of Sil-Pad • Pre-tinned 60/40 solder point for easy grounding PROBLEM: Radio Frequency Interference (RFI) ...
Page 75
... Attach a heat sink to a drive processor ® and Liqui-Bond Liqui-Bond Liquid Adhesives Bergquist Liqui-Bond liquid adhesives are high performance, thermally conductive, liquid gap filling materials.These soft, form-in-place elas- tomers are ideal for coupling “hot” electronic components mounted on PC boards with an adjacent metal case or heat sink. ...
Page 76
... Bergquist has found that reducing the size of the interface pad to roughly 80% of the total interface area actually improves the overall bonding performance while offering significant improvements in total package cooling ...
Page 77
... Actual application performance is directly related to the surface roughness, flatness and pressure applied. Building a Part Number – – – – BP100 0.008 00 1112 NA Note: To build a part number, visit our website at www.bergquistcompany.com. Bond-Ply ® : U.S. Patent 5,090,484 and others. Bond-Ply ® 100 METRIC VALUE TEST METHOD White Visual Fiberglass — ...
Page 78
... Shelf Life: The double-sided pressure sensitive adhesive used in Bond-Ply products requires the use of dual liners to protect the surfaces from contaminants. Bergquist recommends a 6-month shelf life at a maximum continuous storage temperature of 35°C, or 3-month shelf life at a maximum continuous storage temperature of 45°C, for maintenance of controlled adhesion to the liner ...
Page 79
... The ASTM D5470 (Bergquist modified) test fixture was used.The recorded value includes interfacial thermal resistance.These values are provided for reference only. Actual application performance is directly related to the surface roughness, flatness and pressure applied. Shelf Life: The double-sided pressure sensitive adhesive used in Bond-Ply products requires the use of dual liners to protect the surfaces from contaminants. Bergquist recommends a 6-month shelf life at a maximum continuous storage temperature of 35° ...
Page 80
... Discrete component to heat spreader Configurations Available: • With or without glass beads Building a Part Number – – – – LBSA1000 00 00 30cc NA Note: To build a part number, visit our website at www.bergquistcompany.com. METRIC VALUE TEST METHOD Black Black Visual 125,000 ASTM B2196 2.4 2.4 ASTM D792 6 6 — ...
Page 81
... Discrete component to heat spreader Configurations Available: • With or without glass beads Building a Part Number LBSA2000 – 00 – 00 – 30cc – NA Note: To build a part number, visit our website at www.bergquistcompany.com. ™ SA 2000 METRIC VALUE TEST METHOD Yellow Visual 200,000 ASTM B2196 2.4 2.4 ASTM D792 6 6 — ...
Page 82
... TechChat is available Monday - Friday, 8am-5pm, CST. From the simplest of questions to the most complex, Bergquist’s seasoned professionals draw on the company’s extensive experience with thermal management as well as membrane switch, touch screen and electronic component applications. 82 ...
Page 83
... Hi-Flow is commonly used to replace messy thermal grease. Bergquist phase change materials are specially compounded to prevent pump-out of the interface area, which is often associated with thermal grease. Typical applications for Hi-Flow materials include: • ...
Page 84
... Lower Power Application with Gap Pad Top Efficiency In Thermal Materials For Today’s Changing Technology. Contact Bergquist for additional information regarding our Thermal Solutions.We are constantly innovating to offer you the greatest selection of options and flexibility to meet today’s changing technology. Heat ...
Page 85
... Note: Dependent upon material and application requirements, tighter tolerances may be feasible and available. Please contact Bergquist Sales for these requests and additional information regarding tolerances. Sheets: Standard sheet size for most materials is 12" x 12", with or without adhesive as specified on the individual data sheet ...
Page 86
... Note: Bergquist adhesives are designed for ease of application during assembly automated dispensing method is preferred, Bergquist will recommend manufacturers of automated dispensing equipment upon request. Please contact Bergquist Sales for more information on this subject. Note: Bergquist cannot be responsible for dispensing equipment selection and/or performance of specific materials on said equipment the customer’ ...
Page 87
Lead Part Number TO-66 Suffix "A" -84 1.312 .762 Plastic Part Number Power Suffix "A" Various -35 .710 .500 (Clip Mount) -43 .750 .500 TO-126 -50 .437 .312 TO-220 Various -51 .687 .562 Various -52 .855 .630 TO-220 -54 ...
Page 88
Sil-Pad ® Configurations Imperial Measurements Multiwatt C D-DIA Multi-Lead TO-66 Diode Washer Various DO-4 DO-5 DO-4 (oversized) DO-5 (oversized) Various Various Various Various Part Number TO-36 Small Power Devices TO-5, 3 Holes TO-18, 3 Holes TO-18, 4 ...
Page 89
TO-3 & TO-66 Part Number Style -59 Leadless 1.650 I 3 Lead Part Number TO-3 F DIA. 4 Lead Part Number A TO-3 D DIA. ( DIA. (2) 18¡ G¡ Lead Part Number TO-3 10 Lead ...
Page 90
Hi-Flow ® 225 Configurations Imperial Measurements Hi-Flow 225U Tab Configurations ("B") MATERIAL LINER -.500 + .030 PSA STRIP .080+ .000 .040 LINER ("B") ("A") ("A") ("C") Hi-Flow 225UT/225FT Tab Configurations .750 + .063 COLORED PSA TAPE LINER .500 + .030 ...
Page 91
Lead Part Number TO-66 Suffix "A" "B" -84 33.32 19.35 Plastic Part Number Dimensions Power Suffix "A" "B" Various -35 18.03 12.70 (Clip Mount) -43 19.05 12.70 TO-126 -50 11.10 7.92 TO-220 Various -51 17.45 14.27 Various -52 21.72 ...
Page 92
Sil-Pad ® Configurations Metric Measurements Part Number C D-DIA E Multiwatt Suffix -124 B -125 Multi- Lead Part Number A TO-66 Suffix -93 Diode Washer Various DO-4 DO-5 DO-4 (oversized) DO-5 (oversized) Various Various Various Various TO-36 Small Power Devices ...
Page 93
TO-3 Part Number Style -59 Leadless 41. Lead Part Number TO-3 F DIA Lead Part Number D DIA. (4) TO DIA. (2) 18¡ G¡ Lead Part Number TO-3 10 Lead Part Number ...
Page 94
Hi-Flow ® 225 Configurations Metric Measurements Hi-Flow 225U Tab Configurations ("B") MATERIAL LINER -.500 + .030 PSA STRIP .080+ .000 .040 LINER ("B") ("A") ("A") ("C") Hi-Flow 225UT/225FT Tab Configurations .750 + .063 COLORED PSA TAPE LINER .500 + .030 ...
Page 95
P/N 09SPS01-002 (TO-220) P/N 09SPS01-011 (TO-5) P/N 09SPS01-020 (DO-5) Sil-Pad P/N 09SPS01-001 (TO-3) P/N 09SPS01-016 (TO-3) P/N 09SPS01-017 (TO-66) P/N 09SPS01-023 (TO-3) Contact the factory for other configurations. ® Shield Standard Configurations P/N 09SPS01-009 P/N 09SPS01-019 (DO-4) 95 ...
Page 96
...