ECBBK ETERNA, ECBBK Datasheet - Page 2

• Manufacturer Part Number: ECBBK
• Description: BULKHEAD, CORNER, BLK
• Manufacturer: ETERNA

Specifications of ECBBK

• Light Source: 1 X ES GLS 60W
• Colour: Black
• Length: 265mm
• Depth: 95mm
• Svhc: No SVHC (15-Dec-2010)
• Base Type: ES 60W
• External Depth: 95mm
• External Length / Height: 265mm
• External Width: 95mm
• Height: 265mm
• Ip/nema Rating: IP 44
• Width: 95mm
• Lamp Base Type: ES 60W
• Power Rating: 60W

Safety markings:
Read this first:
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
Installation:
1)
2)
3)
4)
5)
6)
7)
This light fitting must be installed in accordance with the Building Regulations. These may
be obtained from HMSO or viewed and downloaded from www.odpm.gov.uk following the link for
Building Regulations.
If in any doubt, consult a qualified electrician.
Switch off the mains before commencing installation and remove the appropriate circuit fuse.
Do not use the fitting without the Diffuser fitted.
Replace the Diffuser if it is cracked or broken.
Suitable for vertical or horizontal outdoor use.
This product is suitable for installation on surfaces with normal flammability ( indicated by the "F" in
a triangle ) e.g. wood, plasterboard, masonry. It is not suitable for use on highly flammable
surfaces ( e.g. polystyrene, textiles ).
Before making fixing hole(s), check that there are no obstructions hidden beneath the mounting
surface such as pipes or cables.
The chosen location of your new fitting should allow for the product to be securely mounted ( e.g.
to brick or concrete ) and safely connected to the mains supply ( lighting circuit ).
The Corner Bulkhead must be positioned so that there is at least 0.5m ( 500mm ) between the
bulkhead and any illuminated surface.
If the location of your new fitting requires the provision of a new electrical supply, the supply must
conform with the requirements of the Building Regulations.
This product is designed for permanent connection to fixed wiring: this should be either a suitable
lighting circuit ( protected with a 5 or 6 Amp MCB or fuse ) or a fused spur ( with a 3 Amp fuse ) via
a fused connection unit. We recommend that the supply incorporates a switch for ease of
operation.
Make connections to the electrical supply in accordance with the following code:
This product must be connected to Earth.
You are advised at every stage of your installation to double-check any electrical connections you
have made. After you have completed your installation there are electrical tests that should be
carried out: these tests are specified in the Wiring Regulations ( BS7671 ) referred to in the
Building Regulations. If in doubt, consult a qualified electrician.
Loosen the 4 screws and remove the grill and diffuser.
Remove the reflector and lamp holder by unscrewing the retaining screws.
Using the fitting as a template mark the fixing holes on the mounting surface.
Drill fixing holes and insert wall plugs supplied.
Make a hole in the grommet just big enough for the incoming main cable.
Insert the grommet in the cable entry hole in the fitting.
Feed the incoming mains cable through the grommet in the fitting.
Live - Brown or Red
Neutral - Blue or Black
Earth - Green and Yellow
IP44
8)
9)
10) Connect the supply cable Live and Neutral wires to the lamp holder and the earth wire to the earth
11) After fixing the bulkhead in place it is recommended that silicone glue (not supplied) is used to seal
12) Replace the lamp holder and secure into place with the screw. Take care not to over tighten the
13) Replace the reflector and secure into place with the screw. Take care not to over tighten the screw.
14) Insert an ES (E27) lamp to the maximum stated wattage marked on the fitting.
15) Replace the diffuser and grill on the front of the fitting and secure with the 4 screws. Take care not to
16) Restore the mains supply and switch on to illuminate your Corner Bulkhead.
Secure the fitting to the mounting surface using the screws with the O rings supplied to maintain the
IP 44 rating. if fixings supplied are not appropriate for your installation, please discard and use your
own fixings.
Strip the outer insulation from the mains supply cable sufficient to fit the silicone tubing over the inner
wires of the supply cable.
terminal located underneath the lamp holder, see opposite for connection to mains supply. Ensure all
connections are secure and no “whiskers” or bare wires are left free of the terminals.
around the screws and incoming mains cable to maintain the IP44 rating.
screw.
over tighten the 4 screws.