AFBR-707SDZ Avago Technologies US Inc., AFBR-707SDZ Datasheet - Page 9

• Manufacturer Part Number: AFBR-707SDZ
• Description: 10Gb ETHERNET TRANSCEIVER, 1310NM
• Manufacturer: Avago Technologies US Inc.

Specifications of AFBR-707SDZ

• Supply Voltage: 3.3V
• Wavelength Typ: 1310nm
• Applications: Gigabit Ethernet
• Data Rate: 10.312Gbd
• Wavelength: 1310nm
• Voltage - Supply: 3.135 V ~ 3.465 V
• Connector Type: LC Duplex
• Mounting Type: SFP+
• Optical Fiber Type: TX/RX
• Data Transfer Rate: 10313MBd
• Operating Temperature Classification: Commercial
• Peak Wavelength: 1355nm
• Package Type: SFP
• Operating Supply Voltage (min): 3.135V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.465V
• Output Current: 20mA
• Operating Temp Range: 0C to 70C
• Mounting: Snap Fit To Panel
• Pin Count: 20
• Leaded Process Compatible: Yes
• Peak Reflow Compatible (260 C): Yes
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Table 3. Absolute Maximum Ratings
Stress in excess of any of the individual Absolute Maximum Ratings can cause immediate catastrophic damage to
the module even if all other parameters are within Recommended Operating Conditions. It should not be assumed
that limiting values of more than one parameter can be applied concurrently. Exposure to any of the Absolute Maxi-
mum Ratings for extended periods can adversely affect reliability.
Parameter
Storage Temperature
Case Operating Temperature
Relative Humidity
Supply Voltage
Low Speed Input Voltage
Two-Wire Interface Input Voltage
High Speed Input Voltage, Single Ended
High Speed Input Voltage, Differential
Low Speed Output Current
Optical Receiver Input Average Power
Note;
1. The module supply voltages, VccT and VccR must not differ by more than 0.5 V or damage to the device may occur.
Table 4. Recommended Operating Conditions
Recommended Operating Conditions specify parameters for which the electrical and optical characteristics hold
unless otherwise noted. Optical and electrical charactristics are not defined for operation outside the Recommend-
ed Operating Conditions, reliability is not implied and damage to the module may occur for such operation over an
extended period of time. The SFP+ Module Power Supply Requirements are specified in the latest revision of the
SFF 8431 MSA.
Parameter
Case Operating Temperature
Module Supply Voltage
Signal Rate
Power Supply Noise Tolerance
including Ripple
Tx Input Single Ended DC
Voltage Tolerance (Ref VeeT)
Rx Output Single Ended Voltage Tolerance
Notes:
1. Ambient operating temperature limits are based on the Case Operating Temperature limits and are subject to the host system thermal design.
2. The Power Supply Filter (PSF) and resulting Power Supply Noise Tolerance (PSNT) are specified in the SFF 8431 MSA. The PSNT value applies over
9
See Figure 7 for the module Tc reference point.
the range from 10Hz to 10MHz.
Symbol
T
T
RH
VccT, VccR
S
C
Symbol
T
VccT, VccR
V
V
C
Minimum
0
3.135
10.311
-0.3
-0.3
Minimum
-40
-40
5
-0.3
-0.5
-0.5
-0.3
-20
Maximum
70
3.465
10.313
66
4.0
4.0
Maximum
100
100
95
3.8
Vcc+0.5
Vcc+0.5
Vcc+0.5
2.5
20
1.5
Unit
°C
V
GBd
mVp-p
V
V
Unit
C
C
%
V
V
V
V
V
mA
dBm
Notes
Note 1
Note 2
Notes
Note 1