S201MC25 ABB, S201MC25 Datasheet - Page 16

• Manufacturer Part Number: S201MC25
• Description: MCB, 1 POLE, 25A, 10KA, C CURVE
• Manufacturer: ABB
• Series: System Pro M Compactr

Specifications of S201MC25

• No. Of Poles: 1
• Voltage Rating Vac: 230V
• Mounting Type: DIN Rail
• Svhc: No SVHC (18-Jun-2010)
• Approval Bodies: IEC/EN 60898, IEC/EN 60947-2, VDE 0641 Part 11, UL 1077, CSA
• Current Rating: 25A
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

System
pro M compact
Installation and operation instructions
Installation
Can be installed in any mounting position due to snap-on fixing to DIN rails EN 60 715, 35 mm width.
A If MCB S 200/S 200 M is installed without cross wiring, hinge the upper part into the DIN rail and push to let the lower part of the device snap
B To release S 200 /S 200 M that are cross-wired with System pro M compact busbars, first remove the clamping screws Then, pull the lower
C The busbar is deallocated and the S 200/S 200 M can be pulled out by lifting the device forwards (2).
D The cross-wiring is re-inserted in the reverse order. First, open the clamping screws and pull out the quick fastener until it locks into place
C Removal when
Operation
after it has triggered, cannot be switched on again off-handedly, the triggering is probably caused by overload.
If the MCB trips again immediately when trying to reclose (let a short period of time elapse), a complete short-circuit, or as the case may
be, earth connection can be assumed.
fault conditions, even if the operating lever is maintained in the ON position by force (trip-free mechanism).
Cleaning the device
MCBs soiled by installation work should be cleaned with a dry, or, if necessary, a damp and soapy cloth. Never use caustic agents or
dissolvents.
Maintenance
STOTZ MCBs are maintenance-free.
Opening the device will lead to a loss of warranty.
For connection cross sections, see page 7.
Feeder optional, top or bottom, terminal designation according to EN 50 005.
16
A Assembly,
MCBs are switched on by switching the operating lever into the upper position (with resepct to the text block of the nameplate). If an MCB,
Do not try and continuously re-close an existing short circuit or earth fault. The MCB even trips under overload, or short-circuit or earth
Connection:
For wiring diagrams, see picture to the right.
Attention: Do not forget to re-tighten the clamping screws.
pro M compact
cross wiring
remains in place
disassembly
without
pro M compact
cross wiring
into place (1). The device is released in the reverse order, after the quick fastener has been removed with a screw driver (2).
part of the S 200/S 200 M forwards (1) and lift it straight up (1a) , then, the quick fastener (1b) will recede.
for the first time (3) . Then, take the S 200 /S 200 M and insert it with rear terminal side onto the pins of the System pro M compact busbar
(4) , turn it into the direction of the DIN rail (4a) and shift it vertically downwards (4b) ,this way, the quick fasterner snaps back into place
(4c).
quick
fastener
pro M compact
busbar
snap on
pin
®
Miniature circuit-breakers
S 200/S 200 M series
release
D Insertion when
pro M compact
cross wiring
remains in place
B Detaching when
pro M compact
cross wiring
remains in place
pin
pro M compact
busbar
pro M compact
busbar