AM-1435MC Murata Power Solutions Inc, AM-1435MC Datasheet - Page 2

• Manufacturer Part Number: AM-1435MC
• Description: Amplifer
• Manufacturer: Murata Power Solutions Inc

7-4
AM-1435
FUNCTIONAL SPECIFICATIONS
(Typical at +25°C and ±15V supplies, unless otherwise noted.)
INPUT
Differential Between Inputs
Common Mode Voltage Range
Common Mode Rejection Ratio
Input Impedance
Input Bias Current
Input Offset Current
Input Offset Voltage
PERFORMANCE
DC Open Loop Gain
Input Offset Voltage Drift
Input Bias Current Drift
Input Offset Current Drift
Input Voltage Noise
Input Current Noise
Power Supply Rejection Ratio
DYNAMIC CHARACTERISTICS
Gain Bandwidth Product
Unity Gain Bandwidth
Full Power Frequency
Settling Time
Slew Rate
Overshoot
Propagation Delay
Rise Time (10V step)
Overload Recovery Time
OUTPUT
Output Voltage
Output Current
Stable Capacitative Load
POWER REQUIREMENTS
Rated Supply Voltages
Quiescent Current
Footnotes:
1MHz
DC
Common Mode
Differential Mode
0.01Hz to 10Hz
100Hz to 10kHz
10Hz to 1MHz
0.01Hz to 10Hz
100Hz to 10kHz
10Hz to 1MHz
10V to ±0.025%
10V to ±0.01%
5V to ±1.0%
5V to ±0.1%
1V to ±1.0%
1V to ±0.1%
Specified for dc linear operation. Common mode voltage range prior to fault
condition is ±10V maximum.
Adjustable to zero.
R
Referred to input.
C1 = 0.5pF.
C1 = 1pF.
C1 = 3pF, noise gain >2.
Requires 18°C/W heat sink above +85°C.
L
= 500 .
DATEL, Inc., 11 Cabot Boulevard, Mansfield, MA 02048-1194 (U.S.A.) Tel: [phone] Fax: [phone] • For immediate assistance 800-233-2765
MIN.
±250
700
±10
±12
±7
±5
—
—
80
—
—
—
—
—
90
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
8
2.5 2
TYP.
±0.15
1 2
1000
±300
1000
±8.5
±0.3
100
±20
100
±50
150
±14
±15
±22
1.6
5.2
2.5
2.5
3.5
—
70
±2
±5
±2
15
10
60
70
25
40
10
20
40
50
±7
1
5
MAX.
±100
±25
±16
±30
±4
40
±5
—
—
75
60
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
M
k
UNITS
µVrms
µVrms
nArms
nArms
µV/°C
nA/°C
nA/°C
µVp-p
nAp-p
mV/V
Volts
Volts
MHz
MHz
MHz
Volts
Volts
V/µs
mV
mA
mA
dB
dB
µA
µA
dB
ns
ns
ns
ns
ns
pF
ns
ns
ns
%
ns
pF
pF
PHYSICAL/ENVIRONMENTAL
TECHNICAL NOTES
1. The use of good high-frequency circuit board layout
2. Operation of the AM-1435MM and MM-QL over the +85 to
3. No input protection is provided so as to maximize
4. A 1µF bypass capacitor (C4) connected from OPTIONAL
5. To ensure stable operation when the noise gain is less than
6. The AM-1435 is a prime choice as a current-to-voltage
PARAMETERS
Operating Temp. Range, Case
Storage Temp. Range
Package Type
AM-1435MC
AM-1435MM, MM-QL
techniques is required for rated performance. The
extensive use of a ground plane for all common
connections is recommended. Lead lengths should be
kept to a minimum with point-to-point connections wired
directly to the amplifier pins. 1µF tantalum bypass
capacitors should be used at the ±15V supply pins.
+125°C temperature range requires additional thermal
dissipation to achieve rated performance. Use of an
18°C/W heat sink is recommended.
frequency response. As a result, several precautions must
be observed. Do not apply the positive supply voltage
before the negative supply. Do not apply signals to either
input prior to power-up. If frequency response is not
critical, installation of an external input-protection circuit is
recommended.
BYPASS CAPACITOR (pin 1) to COMMON (pin 14) may be
required to inhibit output oscillation when driving capacitive
loads.
10, a 2pF compensation capacitor (C1) must be connected
between pins 3 and 7. The value of the compensation
capacitor may be application sensitive.
converter due to its excellent E
coefficient ratings. Input bias currents are easily
compensated by adding a resistor from pin 8 to ground,
which is equal to the parallel combination of the feedback
resistor and input impedance.
ABSOLUTE MAXIMUM RATINGS, ALL MODELS
Positive Supply, Pin 4
Negative Supply, Pin 12
Lead Temperature (soldering, 10s)
MIN.
–55
–65
0
14-pin, metal-sealed, ceramic DIP
OS
and I
®
TYP.
+18V
–18V
300°C
—
—
—
OS
temperature
MAX.
+125
+150
+70
UNITS
°C
°C
°C
®