AM-1435MC Murata Power Solutions Inc, AM-1435MC Datasheet - Page 2

no-image

AM-1435MC

Manufacturer Part Number
AM-1435MC
Description
Amplifer
Manufacturer
Murata Power Solutions Inc
Datasheets
FUNCTIONAL SPECIFICATIONS
(Typical at +25°C and ±15V supplies, unless otherwise noted.)
Footnotes:
DATEL
➀ Specifi ed for dc linear operation. Common mode voltage range prior to fault
➁ Adjustable to zero.
➂ R
➃ Referred to input.
➄ C1 = 0.5pF.
➅ C1 = 1pF.
➆ C1 = 3pF, noise gain >2.
➇ Requires 18°C/W heat sink above +85°C.
INPUT
Differential Between Inputs
Common Mode Voltage Range ➀
Common Mode Rejection Ratio
Input Impedance
Input Bias Current
Input Offset Current
Input Offset Voltage ➁
DC Open Loop Gain ➂
Input Offset Voltage Drift
Input Bias Current Drift
Input Offset Current Drift
Input Voltage Noise
Input Current Noise ➃
Power Supply Rejection Ratio
DYNAMIC CHARACTERISTICS
Gain Bandwidth Product
Unity Gain Bandwidth
Full Power Frequency ➄
Settling Time
Slew Rate ➄
Overshoot
Propagation Delay
Rise Time (10V step)
Overload Recovery Time
OUTPUT
Output Voltage ➂
Output Current ➂
Stable Capacitative Load ➆
POWER REQUIREMENTS
Rated Supply Voltages
Quiescent Current
PERFORMANCE
condition is ±10V maximum.
1MHz
DC
Common Mode
Differential Mode
0.01Hz to 10Hz
100Hz to 10kHz
10Hz to 1MHz
100Hz to 10kHz
10Hz to 1MHz
10V to ±0.025% ➅
10V to ±0.01% ➅
5V to ±1.0%
5V to ±0.1%
1V to ±1.0%
1V to ±0.1%
0.01Hz to 10Hz
L
®
= 500Ω.
MIN.
±250
700
±10
±12
±7
73
90
±5
8
2.5 ❘❘ 2
±0.15
TYP.
®
1 ❘❘ 2
1000
±300
1000
±0.3
±8.5
100
±20
100
±50
150
±14
±15
±22
1.6
5.2
2.5
2.5
3.5
70
±2
±5
±2
15
10
60
70
25
40
10
20
40
50
±7
1
5
• 11 Cabot Boulevard, Mansfi eld, MA 02048-1151 USA • Tel: (508) 339-3000 • www.datel.com • e-mail: help@datel.com
MAX.
±100
±25
±16
±30
±4
40
±5
60
MΩ ❘❘ pF
UNITS
kΩ ❘❘ pF
μVrms
μVrms
nArms
nArms
μV/°C
nA/°C
nA/°C
μVp-p
nAp-p
mV/V
Volts
Volts
MHz
MHz
MHz
V/μs
Volts
Volts
mV
mA
mA
dB
dB
μA
μA
dB
pF
ns
ns
ns
ns
ns
ns
ns
ns
ns
%
TECHNICAL NOTES
1. The use of good high-frequency circuit board layout
2. Operation of the AM-1435MM and MM-QL over the +85
3. No input protection is provided so as to maximize frequency
4. A 1μF bypass capacitor (C4) connected from OPTIONAL
5. To ensure stable operation when the noise gain is less than
6. The AM-1435 is a prime choice as a current-to-voltage
PHYSICAL/ENVIRONMENTAL
Operating Temp. Range, Case
AM-1435MC
AM-1435MM, MM-QL ➇
Storage Temp. Range
Package Type
ABSOLUTE MAXIMUM RATINGS, ALL MODELS
Positive Supply, Pin 4
Negative Supply, Pin 12
Lead Temperature (soldering, 10s)
techniques is required for rated performance. The extensive
use of a ground plane for all common connections is
recommended. Lead lengths should be kept to a minimum
with point-to-point connections wired directly to the amplifi er
pins. 1μF tantalum bypass capacitors should be used at the
±15V supply pins.
to +125°C temperature range requires additional thermal
dissipation to achieve rated performance. Use of an
18°C/W heat sink is recommended.
response. As a result, several precautions must be
observed. Do not apply the positive supply voltage before
the negative supply. Do not apply signals to either input prior
to power-up. If frequency response is not critical, installation
of an external input-protection circuit is recommended.
BYPASS CAPACITOR (pin 1) to COMMON (pin 14) may be
required to inhibit output oscillation when driving capacitive
loads.
10, a 2pF compensation capacitor (C1) must be connected
between pins 3 and 7. The value of the compensation
capacitor may be application sensitive.
converter due to its excellent E
coeffi cient ratings. Input bias currents are easily
compensated by adding a resistor from pin 8 to ground,
which is equal to the parallel combination of the feedback
resistor and input impedance.
Ultra-Fast, Wideband Operational Amplifi ers
01 Apr 2011 MDA_AM-1435.B02 Page 2 of 4
MIN.
–55
–65
0
+18V
–18V
300°C
14-pin, metal-sealed, ceramic DIP
OS
and I
TYP.
OS
AM-1435
temperature
MAX.
+125
+150
+70
UNITS
°C
°C
°C

Related parts for AM-1435MC