SNAP-PAC-EB2-W OPTO 22, SNAP-PAC-EB2-W Datasheet - Page 4

• Manufacturer Part Number: SNAP-PAC-EB2-W
• Description: I/O Processor Wireless
• Manufacturer: OPTO 22
• Type: PC Basedr

Specifications of SNAP-PAC-EB2-W

• Accessory Type: Communication Processor
• Signal Input Type: Ethernet, RS-232
• Brand/series: SNAP Series
• Communication: RS-485
• Current, Input: 750 mA
• Dimensions: 3.3 L × 1.83 W × 4.28 H In.
• Input Type: Analog/Digital/Serial
• Memory: 16 MB RAM
• Mounting Type: Rack
• Network Protocols: IEEE 802.3
• Output Type: Analog/Digital/Serial
• Primary Type: Controller
• Temperature, Operating: 0 to 60 °C
• Voltage, Supply: 5-5.2 VDC
• Rohs Compliant: Yes
• For Use With: SNAP PAC System
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PAGE
4
LEDs and Network Interfaces—Wired Ethernet Brains
This diagram applies to part numbers SNAP-PAC-EB1, SNAP-PAC-EB2, SNAP-PAC-EB1-FM, and SNAP-PAC-EB2-FM.
LEDs and Network Interfaces—Wired+Wireless Ethernet Brains
This diagram applies to part numbers SNAP-PAC-EB1-W and SNAP-PAC-EB2-W.
Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com
SALES 800-321-6786 • 951-695-3000 • FAX [phone] • [e-mail] • SUPPORT 800-835-6786 • 951-695-3080 • FAX [phone] • [e-mail]
© 2007–2011 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
LEDs
Switched Ethernet network
interfaces
Brains can be networked in a
daisy-chain configuration or in a
standard star configuration using
either Ethernet interface. Both
interfaces use the same IP address.
NOTE: When using a daisy-chain
configuration, be aware that if
power to a brain is lost, all brains
beyond it on the network will also
lose communication. Firmware on
daisy-chained brains must be
updated one at a time.
Status and activity LEDs
WLAN
STAT
LED
LNK
ACT
Ethernet LEDs
MS
NS
Link established with Ethernet network
Activity on Ethernet network
Brain status
EtherNet/IP Module status
EtherNet/IP Network status
Wireless LAN status
WLAN LED
Indicates
Brain reset button
Note on switched Ethernet network interfaces
For a wired network, brains can be set up in a daisy-chain
configuration or a standard star configuration using
either the Ethernet1 or Ethernet2 network interface. Both
interfaces use the same IP address.
When using a daisy-chain configuration, be aware that if
power to a brain is lost, all brains beyond it on the
network will also lose communication. Firmware on
daisy-chained brains must be updated one brain at a
time.
The WLAN interface does not provide access to other
brains in a daisy-chain configuration, as this interface has
a separate IP address.
Switched network
interface
Wireless LAN antenna
LEDs
Unnamed
STAT
LED
LNK
ACT
MS
NS
Link established with Ether-
net network
Activity on Ethernet network
Brain status
EtherNet/IP Module Status
EtherNet/IP Network Status
Reserved for future use
Indicates
SNAP PAC Brains