LM5 BANNER ENGINEERING, LM5 Datasheet
LM5
Specifications of LM5
Available stocks
Related parts for LM5
LM5 Summary of contents
Page 1
MULTI-BEAM Compact modular self-contained photoelectric sensing controls 1.6" (40 mm) 4.5" (114 mm) 1/2" – 14 NPSM Conduit Entrance 5 mm (#10) Screw Clearance (4) (30.0 mm) Printed in USA ® Sensors Status Indicator LED (except emitters) Access to Sensitivity ...
Page 2
... NOT be used as sensing devices for personnel protection. WARRANTY: Banner Engineering Corporation warrants its products to be free from defects for one year. Banner Engineering Corporation will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. ...
Page 3
MULTI-BEAM Sensors E71083 Banner MULTI-BEAM ® sensors are compact modular self con- tained photoelectric switches. Each MULTI-BEAM consists of three components: scanner block, power block, and logic module. The scanner block contains the complete modulated photoelectric amplifier as well as ...
Page 4
Selection of MULTI-BEAM Components MULTI-BEAM sensors are made up of three components: scanner block, power block, and logic module. This is true for all MULTI- BEAMs with the exception of opposed mode emitter units which require only a power block ...
Page 5
... PBA PBAQ PBAT PBO PBAM PBA-1 PBB PBBT PBOB PBB-1 Logic Modules Model LM1 LM3 LM5 LM5R LM5-14 LM5T LM4-2 LM4-2NR LM8-1 LM8A LM6-1 LM8 LM2 LM10 LMT 2-wire Systems (pages 24 through 29) Scanner Blocks Model SBE & 2SBR 2SBL1 2SBD1 2SBDX1 ...
Page 6
... Model 2PBD 2PBA 2PBB 2PBR 2PBR2 Logic Modules Model 2LM3 2LM5 2LM5R 2LM5-14 2LM5T 2LM4-2 LMT MULTI-BEAM Other Systems Edgeguide Systems (data sheet 03506) MULTI-BEAM 3- & 4-WIRE SCANNER BLOCKS DESCRIPTION MULTI-BEAM 3- & 4-wire scanner blocks offer a complete comple- ment of sensing modes. There are 3 or more models for each sensing mode, resulting in a choice of exactly the right sensor for any applica- tion ...
Page 7
MULTI-BEAM Sensing Mode OPPOSED Mode OBJECT 3- & 4-wire Scanner Blocks Models Excess Gain SBE/SBR1: this opposed pair has the highest gain available response. SBED/SBRD1: fast response and small effective beam; will detect objects as small as ...
Page 8
MULTI-BEAM Sensing Mode RETROREFLECTIVE Mode RETRO TARGET OBJECT NOTE: for detailed information on available retroreflective materials, see the Banner product catalog & 4-wire Scanner Blocks Models Excess Gain SBLV1: visible beam makes alignment very easy, and is the ...
Page 9
MULTI-BEAM Sensing Mode DIFFUSE Mode OBJECT APPLICATION NOTE general rule regarding background objects in diffuse sens- ing, verify that the distance to the nearest background object is at least three times the distance from the sensor to the ...
Page 10
MULTI-BEAM Sensing Mode CONVERGENT Mode OBJECT Counting radiused products 10 3- & 4-wire Scanner Blocks Models Excess Gain SBCV1: .06-inch (1.5mm) dia. visible red spot, for precise positioning, edge-guiding, & small parts detection. Sensor-to-product distance must be consistent. Some products ...
Page 11
... HIGH-POWER SCANNER BLOCK OPPOSED MODE OBJECT DIFFUSE MODE OBJECT For complete information on glass fiber optic assemblies and accessories, see product catalog. 3- & 4-wire Scanner Blocks Models Excess Gain SBEF & SBRF1 1000 Range: see excess gain curve Response: 1ms on/off E Repeatability: 0 ...
Page 12
... FIBER OPTIC Mode (glass fiber optics) VERY HIGH-SPEED SCANNER BLOCK OPPOSED MODE OBJECT DIFFUSE MODE OBJECT For complete information on glass fiber optic assemblies and accessories, see Banner product catalog & 4-wire Scanner Blocks Models Excess Gain SBF1 1000 Range: see excess gain ...
Page 13
MULTI-BEAM Sensing Mode FIBER OPTIC Mode (glass fiber optics) VISIBLE RED LIGHT SOURCE OPPOSED MODE OBJECT RETROREFLECTIVE MODE RETRO TARGET OBJECT DIFFUSE MODE OBJECT Scanner block model SBFV1 supplies visible red light to the emitter half of a glass fiber ...
Page 14
... Any objects passing over the sensor would then cast a shadow, resulting in an output (dark operate). Ambient receivers are used with LM5-14 delay logic to sense daylight for outdoor lighting control. These sensors can also sense the large amounts of infrared light (heat energy) which is emitted by hot or molten glass, metal, or plastic during processing of these materials ...
Page 15
MULTI-BEAM DC Models PBT Input 30V dc at less than 60mA (current draw depends on scanner block used). 10% max. ripple. Output: one open-collector NPN transistor (sinks current to negative side of power supply). 250mA maximum. On state ...
Page 16
MULTI-BEAM DC Models These are power blocks for emitter scanner blocks only (models SBE, SBED, SBEX, SBEV, SBEXD, SBEF, SBEXF). Emitter assemblies do not require logic modules. PBT-1 Input 30V dc at less than 60mA (current draw depends ...
Page 17
MULTI-BEAM Hookup Diagrams for DC Power Blocks (continued) Hookup to MAXI-AMP Logic Module The current sinking output(s) of MULTI-BEAM power block models PBT and PBT2 may be connected directly to the input of CL Series MAXI-AMP modules. A MAXI-AMP which ...
Page 18
MULTI-BEAM AC Models PBAT Input: 105 to 130V ac, 50/60Hz. Output: SPST isolated solid-state switch; 100mA maximum (no inrush capacity), 200V dc max., 140V ac max. On-state voltage drop: less than 3 volts at full load. Off-state leakage current: less ...
Page 19
... LM3 can program any power block for normally open or normally closed operation via the light/dark operate jumper. NOTE: model PBAQ is not comaptible with logic module models LM5 and LM5-14. For normally closed on-delay logic, use PBA with LM5R and reverse the light/dark function. ...
Page 20
MULTI-BEAM Hookup Diagrams for AC Power Blocks (continued) Hookup in Parallel with other MULTI-BEAMs Any number of 3- & 4-wire L1 MULTI-BEAM power block outputs may be connected in parallel to a load. Parallel sen- PBA sor connection is usually ...
Page 21
MULTI-BEAM Functional Schematic RESPONSE TIME: response time will be that for the scanner block (plus power block) plus the programmed delay (if the logic includes a delay function). Model and Function LM1 on-off OUTPUT SIGNAL LM2 alternate action OUTPUT SIGNAL ...
Page 22
... If the input signal is gone for longer than the off-delay time, the output finally drops out. The most common use for the LM5- control fill level, for example in a bin: when the bin is full, a beam is broken, and a predetermined time later, the flow is stopped. After the level has fallen below the beam for a time, the flow is restarted ...
Page 23
... For fixed timing, the letter "F" should always be followed by the desired time, . seconds in seconds (e.g., LM5MF1 would be an LM5 on-delay with a fixed 1 second . second delay time). For fractions of seconds, use decimal equivalents, such seconds LM5MF.5, or LM5MF.01, etc. ...
Page 24
MULTI-BEAM 2-wire Sensors 2-wire MULTI-BEAM Functional Schematic, 2-wire MULTI-BEAM MULTI-BEAM 2-Wire Scanner Blocks SPECIFICATIONS SUPPLY VOLTAGE: connections are made via a 2-wire power block (see page 27). RESPONSE TIME: 10 milliseconds ON and OFF (3000 operations per minute). NOTE: a ...
Page 25
MULTI-BEAM Sensing Mode OPPOSED Mode OBJECT RETROREFLECTIVE RETRO TARGET OBJECT CONVERGENT Mode OBJECT 2-wire Scanner Blocks Models Excess Gain 1000 SBE & 2SBR1 100 E Range: 150 feet (45m Response: 10ms on/off G 10 Repeatability: ...
Page 26
... Models 2SBD1 and 2SBDX1 diffuse (proximity) mode scanner blocks are identical except for their lenses. Model 2SBD1 uses upper cover model UC-D, and the 2SBDX1 uses UC-L (see MULTI-BEAM Accessories, pages 30- 31). While the UC-L lens extends the range to over 30 inches, it creates a "dip" in the excess gain at closer ranges. ...
Page 27
MULTI-BEAM MULTI-BEAM 2-wire power block models 2PBA, 2PBB, and 2PBD contain a low voltage power supply which utilizes a unique circuit to take a very small leakage current through the load and convert it to the dc power required to ...
Page 28
MULTI-BEAM Hookup Diagrams for 2-wire Power Blocks NOTE: output has maximum load capacity of 3/4 amp; maximum resistive load 15K ohms, minimum inductive load 1.2 watts (10mA) Basic Hookup of 2-wire MULTI-BEAM (See Specifications) 2PBA 2PBB 2PBD ...
Page 29
... This is referred "retriggerable" one shot, and this feature may be applied to some rate sensing applications. The 2LM5 is a true "on-delay" type logic module. The input signal must be present for a predetermined length of time before the output is energized. The output then remains energized until the input signal is removed ...
Page 30
... Upper covers may be ordered as replacement parts or for modifying the optical response of a particular model scanner block. The following upper cover assemblies are standard and stocked. Other special variations may be quoted. Stainless steel hardware is included with each cover. NOTE: See the MULTI-BEAM Accessories section of the Banner product catalog for information on interchangeability of upper covers between various scanner block models. ...
Page 31
... MULTI-BEAM Accessories Mounting Brackets SMB700 Model (right general-purpose two-axis mount- ing bracket that is supplied with a cable gland assembly which is used to attach the MULTI-BEAM wiring base to the bracket. The gland assembly is threaded through the bracket and into the conduit entrance at the base of the scanner block. A large lock- washer is supplied to hold the scanner block firmly in place ...
Page 32
... NOT be used as sensing devices for personnel protection. WARRANTY: Banner Engineering Corporation warrants its products to be free from defects for one year. Banner Engineering Corporation will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products ...