PBT BANNER ENGINEERING, PBT Datasheet
Specifications of PBT
Available stocks
Related parts for PBT
PBT Summary of contents
Page 1
MULTI-BEAM Compact modular self-contained photoelectric sensing controls 1.6" (40 mm) 4.5" (114 mm) 1/2" – 14 NPSM Conduit Entrance 5 mm (#10) Screw Clearance (4) (30.0 mm) Printed in USA ® Sensors Status Indicator LED (except emitters) Access to Sensitivity ...
Page 2
... NOT be used as sensing devices for personnel protection. WARRANTY: Banner Engineering Corporation warrants its products to be free from defects for one year. Banner Engineering Corporation will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. ...
Page 3
MULTI-BEAM Sensors E71083 Banner MULTI-BEAM ® sensors are compact modular self con- tained photoelectric switches. Each MULTI-BEAM consists of three components: scanner block, power block, and logic module. The scanner block contains the complete modulated photoelectric amplifier as well as ...
Page 4
Selection of MULTI-BEAM Components MULTI-BEAM sensors are made up of three components: scanner block, power block, and logic module. This is true for all MULTI- BEAMs with the exception of opposed mode emitter units which require only a power block ...
Page 5
... Systems Power Blocks Model PBT PBT2 PBP PBT-1 PBT48 PBP48 PBT48-1 PBD-2 PBD PBD-1 PBA PBAQ PBAT PBO PBAM PBA-1 PBB PBBT PBOB PBB-1 Logic Modules Model LM1 LM3 LM5 LM5R LM5-14 LM5T LM4-2 LM4-2NR LM8-1 LM8A LM6-1 LM8 ...
Page 6
Systems (pages 24 through 29) Power Blocks Model 2PBD 2PBA 2PBB 2PBR 2PBR2 Logic Modules Model 2LM3 2LM5 2LM5R 2LM5-14 2LM5T 2LM4-2 LMT MULTI-BEAM Other Systems Edgeguide Systems (data sheet 03506) MULTI-BEAM 3- & 4-WIRE SCANNER BLOCKS DESCRIPTION MULTI-BEAM ...
Page 7
MULTI-BEAM Sensing Mode OPPOSED Mode OBJECT 3- & 4-wire Scanner Blocks Models Excess Gain SBE/SBR1: this opposed pair has the highest gain available response. SBED/SBRD1: fast response and small effective beam; will detect objects as small as ...
Page 8
MULTI-BEAM Sensing Mode RETROREFLECTIVE Mode RETRO TARGET OBJECT NOTE: for detailed information on available retroreflective materials, see the Banner product catalog & 4-wire Scanner Blocks Models Excess Gain SBLV1: visible beam makes alignment very easy, and is the ...
Page 9
MULTI-BEAM Sensing Mode DIFFUSE Mode OBJECT APPLICATION NOTE general rule regarding background objects in diffuse sens- ing, verify that the distance to the nearest background object is at least three times the distance from the sensor to the ...
Page 10
MULTI-BEAM Sensing Mode CONVERGENT Mode OBJECT Counting radiused products 10 3- & 4-wire Scanner Blocks Models Excess Gain SBCV1: .06-inch (1.5mm) dia. visible red spot, for precise positioning, edge-guiding, & small parts detection. Sensor-to-product distance must be consistent. Some products ...
Page 11
... HIGH-POWER SCANNER BLOCK OPPOSED MODE OBJECT DIFFUSE MODE OBJECT For complete information on glass fiber optic assemblies and accessories, see product catalog. 3- & 4-wire Scanner Blocks Models Excess Gain SBEF & SBRF1 1000 Range: see excess gain curve Response: 1ms on/off E Repeatability: 0 ...
Page 12
... Response time of a MULTI-BEAM sensor is also a function of the power block. For this reason, only power blocks which switch dc (e.g. PBT, PBP, PBO, PBAT, etc) should be used if the fast response time of the scanner block utilized ...
Page 13
... Fibers allow a match of the light image to the geometry of the registration mark. Scanner block model SBFVG1 will sense most bold color differences, including red-on-white. Use only power blocks which switch dc (e.g. PBT, PBP, PBO, PBAT, etc.) for fast response. Beam Pattern SBFV1 1 ...
Page 14
MULTI-BEAM Sensing Mode AMBIENT LIGHT RECEIVER NOTE: MULTI-BEAM ambient light re- ceivers do not have the Alignment Indicating Device (AID™) signal strength feature. The alignment indicator is "ON" steadily when enough light is sensed. FIBER OPTIC AMBIENT LIGHT RECEIVER (glass ...
Page 15
... PBT: the most commonly used dc power block. Its output is an NPN transistor, which sinks current to the negative side of the power supply. The load is connected between the output and the positive side of the power supply. Switching capacity is 250mA. There is no connection to terminal #4. ...
Page 16
... PBT PBT2 (-) 30V dc + PBP com +10 to 30V dc Hookup of DC Emitter MULTI-BEAM emitter-only scanner blocks use dc power block models PBT-1 or PBT48-1. These power blocks connect directly across the dc supply, as shown. - Emitter models: SBE SBED SBEX PBT-1 SBEV SBEXD 1 SBEF SBEXF 10 to 30V ...
Page 17
... Hookup Diagrams for DC Power Blocks (continued) Hookup to MAXI-AMP Logic Module The current sinking output(s) of MULTI-BEAM power block models PBT and PBT2 may be connected directly to the input of CL Series MAXI-AMP modules. A MAXI-AMP which is powered by ac voltage offers a dc supply with enough capacity to power one MULTI-BEAM sensor shown in this hookup diagram ...
Page 18
MULTI-BEAM AC Models PBAT Input: 105 to 130V ac, 50/60Hz. Output: SPST isolated solid-state switch; 100mA maximum (no inrush capacity), 200V dc max., 140V ac max. On-state voltage drop: less than 3 volts at full load. Off-state leakage current: less ...
Page 19
MULTI-BEAM AC Models PBAQ Input: 105 to 130V ac, 50/60Hz. Output: SPST isolated solid-state switch; nor- mally closed, 3/4 amp maximum (derated to 1/2 amp at 70 degrees C). Maximum inrush: 10 amps for one second or 30 amps for ...
Page 20
MULTI-BEAM Hookup Diagrams for AC Power Blocks (continued) Hookup in Parallel with other MULTI-BEAMs Any number of 3- & 4-wire L1 MULTI-BEAM power block outputs may be connected in parallel to a load. Parallel sen- PBA sor connection is usually ...
Page 21
... DARK signal, the output is de-energized. This is referred to as the LIGHT operate mode. If the application calls for DARK operate mode, the LM1 may be used with normally-closed type power blocks such as PBAQ or PBT2. The LM2 provides "flip-flop" or toggling action of the power block output, such that each time the scanner block changes from a DARK state to a LIGHT state, the output changes state ...
Page 22
MULTI-BEAM Model and Function LM4-2NR one-shot (non-retriggerable) Pulse Pulse Pulse OUTPUT SIGNAL Setable time range second. LM5 on-delay Delay OUTPUT SIGNAL Setable time range: 1 seconds. LM5R off-delay Hold Hold OUTPUT SIGNAL Setable time range: ...
Page 23
MULTI-BEAM Model and Function LM8 repeat cycler Delay Hold Delay Hold Delay Hold OUTPUT SIGNAL Setable time range: 1 seconds. LM8-1 delayed one-shot Delay Hold Delay Hold OUTPUT SIGNAL Setable time range: 1 seconds. LM8A on-delay ...
Page 24
MULTI-BEAM 2-wire Sensors 2-wire MULTI-BEAM Functional Schematic, 2-wire MULTI-BEAM MULTI-BEAM 2-Wire Scanner Blocks SPECIFICATIONS SUPPLY VOLTAGE: connections are made via a 2-wire power block (see page 27). RESPONSE TIME: 10 milliseconds ON and OFF (3000 operations per minute). NOTE: a ...
Page 25
... The SBE emiter uses a 3 & 4 wire power block. Powerblocks for use with SBE include models PBA-1, PBB-1, PBD-1, PBT-1, and PBT48-1 (see pages 16 and 19 for information on these powerblocks). ...
Page 26
... Models 2SBD1 and 2SBDX1 diffuse (proximity) mode scanner blocks are identical except for their lenses. Model 2SBD1 uses upper cover model UC-D, and the 2SBDX1 uses UC-L (see MULTI-BEAM Accessories, pages 30- 31). While the UC-L lens extends the range to over 30 inches, it creates a "dip" in the excess gain at closer ranges. ...
Page 27
MULTI-BEAM MULTI-BEAM 2-wire power block models 2PBA, 2PBB, and 2PBD contain a low voltage power supply which utilizes a unique circuit to take a very small leakage current through the load and convert it to the dc power required to ...
Page 28
MULTI-BEAM Hookup Diagrams for 2-wire Power Blocks NOTE: output has maximum load capacity of 3/4 amp; maximum resistive load 15K ohms, minimum inductive load 1.2 watts (10mA) Basic Hookup of 2-wire MULTI-BEAM (See Specifications) 2PBA 2PBB 2PBD ...
Page 29
MULTI-BEAM SPECIFICATIONS, 2-WIRE LOGIC MODULES: specifications for 2-wire logic modules are identical to those for 3- and 4-wire logic modules (see page 21). Model and Function 2LM3 on-off OUTPUT SIGNAL 2LM4-2 one-shot Hold Pulse Pulse OUTPUT SIGNAL Setable time range: ...
Page 30
... Upper covers may be ordered as replacement parts or for modifying the optical response of a particular model scanner block. The following upper cover assemblies are standard and stocked. Other special variations may be quoted. Stainless steel hardware is included with each cover. NOTE: See the MULTI-BEAM Accessories section of the Banner product catalog for information on interchangeability of upper covers between various scanner block models. ...
Page 31
... MULTI-BEAM Accessories Mounting Brackets SMB700 Model (right general-purpose two-axis mount- ing bracket that is supplied with a cable gland assembly which is used to attach the MULTI-BEAM wiring base to the bracket. The gland assembly is threaded through the bracket and into the conduit entrance at the base of the scanner block. A large lock- washer is supplied to hold the scanner block firmly in place ...
Page 32
... NOT be used as sensing devices for personnel protection. WARRANTY: Banner Engineering Corporation warrants its products to be free from defects for one year. Banner Engineering Corporation will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products ...