PIC16C74B-04/PQ Microchip Technology, PIC16C74B-04/PQ Datasheet - Page 2

• Manufacturer Part Number: PIC16C74B-04/PQ
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,QFP,44PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C74B-04/PQ

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 4MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 7KB (4K x 14)
• Program Memory Type: OTP
• Ram Size: 192 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 44-MQFP, 44-PQFP
• Processor Series: PIC16C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 192 B
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 4 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 8
• Operating Supply Voltage: 2.5 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000, DM163022
• Minimum Operating Temperature: 0 C
• On-chip Adc: 8 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC16C63A/65B/73B/74B
Clarifications/Corrections to the Data
Sheet:
In the Device Data Sheet (DS30605C), the following
clarifications and corrections should be noted.
1. Module: SSP (SPI
FIGURE 10-1:
DS80164A-page 2
RC3/SCK/SCL
RC4/SDI/SDA
RA5/SS/AN4
RC5/SDO
In Section 10.2 (“SPI Mode”), Figure 10-1 and the
note box immediately beneath it have been
amended to better demonstrate the Peripheral OE
line of the SSP module and describe its relation-
ship to the TRISC<5> bit of PORTC.
Changes are indicated in bold.
Peripheral OE
Read
SS Control
TRISC<3>
Select
SMP:CKE
Edge
bit0
Enable
Select
Edge
SSP BLOCK DIAGRAM
(SPI MODE)
TM
2
SSPBUF reg
SSPSR reg
SSPM3:SSPM0
Mode)
Clock Select
4
2
TMR2 Output
Write
Prescaler
4, 16, 64
Clock
Shift
Data Bus
Internal
2
T
CY
Note 1: When the SPI module is in Slave mode
2: If the SPI is used in Slave mode with
3: When the SPI is in Slave mode with SS
with
(SSPCON<3:0> = 0100), the SPI module
will reset if the SS pin is set to V
CKE = '1', then SS pin control must be
enabled.
pin control enabled (SSPCON<3:0> =
0100), the state of the SS pin can affect
the state read back from the TRISC<5>
bit. The Peripheral OE signal from the
SSP module into PORTC, controls the
state that is read back from the
TRISC<5> bit (see Section 5.3 for infor-
mation on PORTC). If Read-Modify-
Write instructions, such as BSF, are
performed on the TRISC register while
the SS pin is high, this will cause the
TRISC<5> bit to be set, thus disabling
the SDO output.
SS
 2003 Microchip Technology Inc.
pin
control
DD
enabled
.