LP2989AIM-5.0 National Semiconductor, LP2989AIM-5.0 Datasheet - Page 6

• Manufacturer Part Number: LP2989AIM-5.0
• Description: IC, LDO VOLT REG, 5V, 0.5A, 8-SOIC
• Manufacturer: National Semiconductor

Specifications of LP2989AIM-5.0

• Primary Input Voltage: 16V
• Output Voltage Fixed: 5V
• Dropout Voltage Vdo: 310mV
• No. Of Pins: 8
• Output Current: 500mA
• Operating Temperature Range: -40°C To +125°C
• Termination Type: SMD
• Filter Terminals: SMD
• Rohs Compliant: No
• Current Rating: 500A
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

www.national.com
SHUTDOWN INPUT
V
I
ERROR COMPARATOR
I
V
V
(MAX)
V
(MIN)
HYST
S/D
OH
S/D
OL
THR
THR
Electrical Characteristics
Limits in standard typeface are for T
less otherwise specified: V
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating the
device outside of its rated operating conditions.
Note 2: ESD testing was performed using Human Body Model, a 100 pF capacitor discharged through a 1.5 kΩ resistor.
Note 3: The maximum allowable power dissipation is a function of the maximum junction temperature, T
and the ambient temperature, T
The value of θ
dependent on PCB trace area, trace material, and the number of layers and thermal vias. For improved thermal resistance and power dissipation for the LLP
package, refer to Application Note AN-1187. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into
thermal shutdown.
Note 4: If used in a dual-supply system where the regulator load is returned to a negative supply, the LP2989 output must be diode-clamped to ground.
Note 5: The output PNP structure contains a diode between the V
on this diode and may induce a latch-up mode which can damage the part (see Application Hints).
Note 6: Limits are 100% production tested at 25˚C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate National’s Average Outgoing Quality Level (AOQL).
Note 7: Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below the value measured with a 1V differential.
Note 8: Temperature coefficient is defined as the maximum (worst-case) change divided by the total temperature range.
Note 9: See Typical Performance Characteristics curves.
Symbol
J−A
Ripple Rejection
Output Voltage
Temperature Coefficient
S/D Input Voltage
S/D Input Current
Output “HIGH” Leakage
Output “LOW” Voltage
Upper Threshold Voltage
Lower Threshold Voltage
Hysteresis
for the SO-8 (M) package is 160˚C/W and the mini SO-8 (MM) package is 200˚C/W. The value θ
Parameter
A
. The maximum allowable power dissipation at any ambient temperature is calculated using:
IN
= V
O
(NOM) + 1V, I
J
= 25˚C, and limits in boldface type apply over the full operating temperature range. Un-
f = 1 kHz, C
(Note 8)
V
V
I
V
V
V
V
I
IN
O
H
L
S/D
S/D
OH
IN
(COMP) = 150 µA
≤ 2 µA
= O/P OFF
= O/P ON
(Continued)
= V
= 16V
= 0
= 5V
Conditions
O
L
(NOM) − 0.5V,
= 1 mA, C
IN
OUT
and V
= 10 µF
OUT
OUT
terminals that is normally reverse-biased. Forcing the output above the input will turn
6
= 4.7 µF, C
Typical
0.001
0.001
0.50
−4.8
−6.6
150
1.4
2.0
60
20
5
IN
= 2.2 µF, V
−13.0
−6.0
−8.3
−8.9
LP2989AI-X.X
Min
1.6
J
(MAX), the junction-to-ambient thermal resistance, θ
(Note 6)
Max
0.18
−3.5
−2.5
−4.9
−3.0
S/D
220
350
−1
15
1
2
J−A
= 2V.
for the LLP (LD) package is specifically
−13.0
−6.0
−8.3
−8.9
Min
1.6
LP2989I-X.X
(Note 6)
Max
0.18
−3.5
−2.5
−4.9
−3.0
220
350
−1
15
1
2
ppm/˚C
%V
Units
mV
dB
µA
µA
V
OUT
J−A
,