SC1410ACQSTRT Semtech, SC1410ACQSTRT Datasheet
SC1410ACQSTRT
Specifications of SC1410ACQSTRT
Related parts for SC1410ACQSTRT
SC1410ACQSTRT Summary of contents
Page 1
... SC1410A Battery Charger Figure 2: Charging Lithium batteries 1N5819 SW VCC Cin 1N5819 10uF PROG 0.1uF BOOST GND VC 6.19k OVP 1uF SENSE BAT Cout + SC1410A 1k 300 22uF 4.2V + 4.2V 1410 SCH42 www.semtech.com 11 to 18V NDS355N 240k 0.25% 100k 0.25% ...
Page 2
... Exceeding the specifications below may result in permanent damage to the device, or device malfunction. Operation outside of the parameters specified in the Electrical Characteristics section is not implied Electrical Characteristics Unless specified 16V 8V VCC BAT BAT 2006 Semtech Corp < V < < ° ° < SC1410A ° ° www.semtech.com ° C ° C ° ...
Page 3
... POWER MANAGEMENT Electrical Characteristics (Cont.) Unless specified 16V 8V VCC BAT BAT 2006 Semtech Corp < > ° ° ± 1 µ SC1410A ° ° µ µ www.semtech.com µ µ µ ...
Page 4
... Pin Configuration TOP VIEW GND BOOST 3 14 GND 4 13 OVP SENSE 7 10 GND 8 9 (16 Pin QSOP) Pin Descriptions 2006 Semtech Corp. Ordering Information Note: GND (1) Only available in tape and reel packaging. A reel VCC2 contains 2500 devices. VCC1 PROG VC NC BAT GND ...
Page 5
... A/A. The programmed output current is therefore given 465 I 2000 I BAT PROG R PROG PROG I BAT where Amps BAT PROG 2006 Semtech Corp. + SHUTDOWN 500kHz OSCILLATOR - - SLOPE - COMP 60k - CA2 + PROG C R PROG PROG As the voltage at the OVP pin rises, reaching V voltage amplifier VA sources current into R I ...
Page 6
... BAT PROG 2006 Semtech Corp. Soft Start - A capacitor on the VC Pin implements the soft start function for the SC1410A. Soft start controls the rate at which output voltage rises so that high cur- rent surges can be avoided or minimized. In order for soft start to be effective, the soft start time must be much longer than the ramp up time of the input supply ...
Page 7
... Io (A) Efficiency at 8.4V output 100% Vout=8.4V Input diode losses included 90% 12V Vin=15V 80% 70% 60% 0.0 0.2 0.4 Io (A) VC Pin characteristics -200 -150 -100 -50 0 0.0 0.5 1.0 V (V) VC 2006 Semtech Corp. 0.6 0.8 1.0 0.6 0.8 1.0 1.5 2.0 7 SC1410A www.semtech.com ...
Page 8
... SEATING PLANE C SIDE VIEW NOTES: 1. CONTROLLING DIMENSIONS ARE IN INCHES (ANGLES IN DEGREES). 2. DATUMS -A- AND -B- 3. DIMENSIONS "E1" AND "D" DO NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. 4. REFERENCE JEDEC STD MO-137, VARIATION AB. 2006 Semtech Corp. A DIM D MIN e A .053 A1 .004 A2 .049 b .008 c .006 ...
Page 9
... POWER MANAGEMENT Land Pattern - QSOP-16 X (C) P NOTES: 1. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. Contact Information Phone: (805)498-2111 FAX (805)498-3804 2006 Semtech Corp. DIM INCHES Semtech Corporation Power Management Products Division ...