DC823B-B Linear Technology, DC823B-B Datasheet - Page 12

• Manufacturer Part Number: DC823B-B
• Description: BOARD EVAL LTM4600HV
• Manufacturer: Linear Technology
• Series: µModuler

Specifications of DC823B-B

• Main Purpose: DC/DC, Step Down
• Outputs And Type: 1, Non-Isolated
• Voltage - Output: 1.2V, 1.5V, 1.8V, 2.5V, 3.3V, 5V
• Current - Output: 10A (Max)
• Voltage - Input: 4.5 V ~ 28 V
• Regulator Topology: Buck
• Frequency - Switching: 1.35MHz
• Board Type: Fully Populated
• Utilized Ic / Part: LTM4600HV
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• Power - Output: -

APPLICATIO S I FOR ATIO
LTM4600HV
After the controller has been started and given adequate
time to charge up the output capacitor, C
short-circuit timer. After the RUN/SS pin charges above 4V,
if the output voltage falls below 75% of its regulated value,
then a short-circuit fault is assumed. A 1.8μA current then
begins discharging C
the RUN/SS pin drops to 3.5V, then the controller turns
off both power MOSFETs, shuting down the converter
permanently. The RUN/SS pin must be actively pulled
down to ground in order to restart operation.
The over-current protection timer requires the soft-start
timing capacitor C
that the output is in regulation by the time C
the 4V threshold. In general, this will depend upon the size
of the output capacitance, output voltage and load current
characteristic. A minimum external soft-start capacitor
can be estimated from:
Generally 0.1μF is more than suffi cient.
Since the load current is already limited by the current
mode control and current foldback circuitry during a
shortcircuit, over-current latchoff operation is NOT always
needed or desired, especially the output has large amount
of capacitance or the load draw huge current during start
up. The latchoff feature can be overridden by a pull-up
current greater than 5μA but less than 80μA to the RUN/SS
pin. The additional current prevents the discharge of C
during a fault and also shortens the soft-start period. Us-
ing a resistor from RUN/SS pin to V
12
C
SS EXT
_
+
1000
SS
U
pF
SS
be made large enough to guarantee
. If the fault condition persists until
>
C
U
OUT
•
V
OUT
IN
W
is a simple solution
(
10
–
SS
3
SS
[ /
F V
is used as a
has reached
U
S
])
SS
to defeat latchoff. Any pull-up network must be able to
maintain RUN/SS above 4V maximum latchoff threshold
and overcome the 4μA maximum discharge current. Figure
3 shows a conceptual drawing of V
short circuit.
1.5V
R
SWITCHING
V
RUN/SS
STARTS
IN
Figure 3. RUN/SS Pin Voltage During Startup and
Short-Circuit Protection
Figure 4. Defeat Short-Circuit Latchoff with a Pull-Up
Resistor to V
OF I
SOFT-START
3V
CLAMPING
L
RELEASED
V
RUN/SS
PGND SGND
IN
4V
LTM4600HV
IN
SHORT-CIRCUIT
LATCH ARMED
4600hv F04
V
O
V
RUN/SS
RECOMMENDED VALUES FOR RUN/SS
10.8V TO 13.8V
OVERLOAD
4.5V TO 5.5V
HAPPENS
24V TO 28V
OUTPUT
V
IN
RUN
during startup and
SHORT-CIRCUIT
R
RUN/SS
75%V
150k
500k
LATCHOFF
50k
O
4600hvfc
4600hv F03
3.5V
t
t