CM1411-03CP ON Semiconductor, CM1411-03CP Datasheet
CM1411-03CP
Specifications of CM1411-03CP
Available stocks
Related parts for CM1411-03CP
CM1411-03CP Summary of contents
Page 1
... EMI both to and from a speaker element. They also support AC signals with a cutoff frequency of 31MHz, enabling audio signals to pass through without distortion. In addition, the CM1411 provides a very high level of protection for sensitive electronic components that may be subjected to electrostatic discharge (ESD). The CM1411 can safely dissipate ESD strikes of ...
Page 2
... Block Diagram Rev Page www.onsemi.com CM1411 ...
Page 3
... Note 1: Parts are shipped in Tape & Reel form unless otherwise specified. Specifications PARAMETER Storage Temperature Range DC Power per Resistor DC Package Power Rating PIN DESCRIPTIONS PART NUMBERING INFORMATION Ordering Part Number CSP CM1411-03CP ABSOLUTE MAXIMUM RATINGS Rev Page www.onsemi.com 2 Lead-free Finish 1 Part Marking CA RATING -65 to +150 ...
Page 4
... Note 3: Clamping voltage is measured at the opposite side of the EMI filter to the ESD pin. For example, if ESD is applied to Pin A1, then clamping voltage is measured at Pin C1. Note 4: Unused pins are left open. CONDITIONS V =5. 10mA LOAD Notes 2 and 4 Notes 2,3 and 10Ω 100pF Rev Page www.onsemi.com CM1411 RATING UNITS -40 to +85 °C (SEE NOTE 1) MIN TYP MAX UNITS Ω ...
Page 5
... CM1411 Performance Information Typical Filter Performance (nominal conditions unless specified otherwise, 50 Ohm Environment) Figure 1. Insertion Loss vs. Frequency (A1-C1 to GND B2) Figure 2. Insertion Loss vs. Frequency (A3-C3 to GND B2) Rev Page www.onsemi.com ...
Page 6
... Figure 6. Lead-free (SnAgCu) Solder Ball Reflow Profile N on-Solder M ask D efined Pad 0.240m m D IA. Solder Stencil Opening 0.300m m D IA. Solder Mask Opening 0.290m m D IA. Rev Page www.onsemi.com CM1411 VALUE 0.240mm Round Non-Solder Mask defined pads 0.290mm Round 0.125mm - 0.150mm 0.300mm Round 50/50 by volume ...
Page 7
... CM1411 Mechanical Details CSP Mechanical Specifications The CM1411 is supplied in a custom Chip Scale Package (CSP). Dimensions are presented below. PACKAGE DIMENSIONS Custom CSP Package Bumps Millimeters Dim Min Nom Max 0.905 0.950 0.995 0.0356 0.0374 0.0392 A1 1.365 1.410 1.455 0.0537 0.0555 0.0573 A2 0 ...
Page 8
... CSP Tape and Reel Specifications PART NUMBER CHIP SIZE (mm) CM1411 1.41 X 0.95 X 0.644 POCKET SIZE (mm) TAPE WIDTH 1.52 X 1.07 X 0.720 8mm Figure 5. Tape and Reel Mechanical Data Rev Page www.onsemi.com REEL QTY PER W DIAMETER REEL 178mm (7") 3500 CM1411 4mm 4mm ...
Page 9
... CM1411 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “ ...