E2EY-X4C1 Omron, E2EY-X4C1 Datasheet - Page 4

• Manufacturer Part Number: E2EY-X4C1
• Description: Proximity Sensors M18 NPN-NO out 4mm Non-ferrous inductiv
• Manufacturer: Omron
• Type: Non-Ferrous Metal Detecting Cylindricalr
• Series: E2EYr

Specifications of E2EY-X4C1

• Maximum Operating Temperature: + 85 C
• Supply Voltage: 30 V
• Operating Supply Voltage: 10 V to 30 V
• Minimum Operating Temperature: - 40 C
• Barrel Size: M18
• Features: High visibility indicator
• Sensing Distance: 4 mm
• Sensor Type: Inductive
• Sensing Object: Metallic
• Response Frequency: 70Hz
• Material - Body: Nickel-Plated Brass
• Shielding: Shielded
• Voltage - Supply: 10 V ~ 30 V
• Output Type: NPN-NO
• Terminal Type: 3-Wire
• Package / Case: Cylinder, Threaded - M18
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Safety Precautions
Refer to Warranty and Limitations of Liability.
This product is not designed or rated for ensuring
safety of persons either directly or indirectly.
Do not use it for such purposes.
Do not use this product under ambient conditions that exceed the
ratings.
● Design
Influence of Surrounding Metal
When mounting the Sensor within a metal panel, ensure that the
clearances given in the following table are maintained. Failure to
maintain these distances may cause deterioration in the performance
of the Sensor.
Influence of Surrounding Metal
Dimensions
E2EY-X4C1
Mounting Hole Dimensions
Model
E2EY-X4C1
E2EY-X8C1
29 dia.
24
F
l
m
Precautions for Correct Use
Item
M18 × 1
0
l
4
42
Two toothed washers
45
WARNING
52
E2EY-X4C1
E2EY-X8C1
60
Two clamping
nuts
18
30
D
Model
d
d dia.
Detection
indicator (red) 6-dia. vinyl-insulated round
D
0
cable with 3 conductors
(Conductor cross section:
0.5 mm
diameter: 1.9 mm),
Standard length: 2 m
18.5
30.5
20
40
m
F (mm)
2
l
, Insulator
+5
0
+5
0
(Unit: mm)
m
dia.
dia.
n
27
45
n
Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified.
E2EY-X8C1
Mutual Interference
When installing Sensors face-to-face or side-by-side, ensure that the
minimum distances given in the following table are maintained.
Mutual Interference
Mounting
Do not tighten the nut with excessive force. A toothed washer must be
used with the nut.
Note: 1. The allowable tightening strength depends on the distance from the
Model
E2EY-X4C1
E2EY-X8C1
Model
E2EY-X4C1
E2EY-X8C1
Note: Aluminum (non-ferrous metal) cannot be detected
2. The following torque assume washers are being used.
edge of the head, as shown in the following table. (A is the distance
from the edge of the head. B includes the nut on the head side. If the
edge of the nut is in part A, the tightening torque for part A applies
instead.)
42 dia.
through iron (ferrous metal).
Tightening
36
Torque
Item
M30 × 1.5
Dimension
100
50
A
(Unit: mm)
(mm)
22
26
Two toothed washers
5
42
Part A
45
35
70
B
52
60
Two
clamping
nuts
Torque
15 N·m
39 N·m
Detection
indicator
(red)
Part B
Part A
6-dia. vinyl-insulated round
cable with 3 conductors
(Conductor cross section:
0.5 mm
ter: 1.9 mm), Standard
length: 2 m
B
A
2
, Insulator diame-
Torque
49 N·m
78 N·m
E2EY
Part B
(Unit: mm)
4