HR10-PC-112 Hirose Electric Co Ltd, HR10-PC-112 Datasheet - Page 11

• Manufacturer Part Number: HR10-PC-112
• Description: CRIMP PIN MALE SILVER FOR HR10A
• Manufacturer: Hirose Electric Co Ltd
• Series: HR10r

Specifications of HR10-PC-112

• Pin Or Socket: Pin
• Wire Gauge: 26-30 AWG
• Contact Termination: Crimp
• Contact Finish: Silver
• Product Type: Contacts
• Contact Style: Pin (Male)
• Mounting Style: Flange
• Termination Style: Crimp
• Shell Plating: Nickel
• Contact Plating: Silver
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: HR1689 - CONN HR10A JACK 20 POS MALEHR1687 - CONN HR10A RECEPT 20POS MALEHR1684 - CONN HR10A PLUG 20POS MALEHR1682 - CONN HR10A JACK 12POS MALEHR1680 - CONN HR10A JACK 10POS MALEHR1678 - CONN HR10A RECEPT 12POS MALEHR1676 - CONN HR10A RECEPT 10POS MALEHR1674 - CONN HR10A PLUG 12POS MALEHR1672 - CONN HR10A PLUG 10POS MALEHR1669 - CONN HR10A RECEPT 6POS MALEHR1667 - CONN HR10A RECEPT 4POS MALEHR1665 - CONN HR10A PLUG 6POS MALEHR1663 - CONN HR10A PLUG 4POS MALEHR1659 - CONN PLUG 12POS MALE CRIMPHR233 - CONN HR10A RECEPT 6POS MALEHR160 - CONN HR10A PLUG 4POS MALE
• Size: -
• Contact Finish Thickness: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: *HR10-PC-112; HR451

■Cable connecting methods
1.Cable end treatment
2. Soldering male pin to cable center
Fig.1
1. Dimensions for cable end treatment are shown in
2.Termination is described below.
Fig.2
1. Solder male pin to cable center conductor as
conductor.
(1). Pre-solder the solder pot of pin with Ø0.5mm
(2). Male pin should fit flush against the cable
(3). Remove any excess solder from the pin with a
(4). A properly soldered terminal will yield 500gf
Fig 1.
(1).Strip cable outer jacket as indicated.
(2).Slit outer jacket on both sides per Fig.1.
(3).Fold back outer cover.
(4).Remove insulator from cable.
indicated in Fig.2.
string solder.
insulator as shown.
knife.This surface must be smooth.
when stretched.
2 pieces (180° reverse side)
Should fix flush
Contact fixing jig
such as vise
Malu pin or Female pin
Slit cable outer jaket
Soldering
(2.5)
11±0.5
3.7±0.2
1.4±0.2
HR10B-2.5CP
HR10B-2.5CJ
3.Crimping cable outer conductor
Fig.3
1. Insert cable prepared per PROCESS 2 into the
2. Crimp this installed metal clamp with tool HR10-
connector.The cable should be inserted until it
comes to a full stop.This may be verified by
checking the dimension from the side of the
connector to the top of the contact(as indicated in
Fig 3). This dimension should be A.
TC-01 per Fig.3 and remove excess insulation with
a knife.
It is possible to pull back the contact.
Hold cable when crimping metal clamp and keep
the dimension to show in Fig 3. after crimping metal
clamp.
(HR10B-2.5CP)
Clamp metal
Table 1 dimenshion A
1.5±0.2mm
2.5CP
Remove excess insulator
material (remaining after
clamping is complated)
with a knife or aimilarobject.
HR10 Series●Push-Pull Connectors
0
2.5CJ
+0.3
0
A
mm
Connector
189