JR16WCCA-4(71) Hirose Electric Co Ltd, JR16WCCA-4(71) Datasheet - Page 7

• Manufacturer Part Number: JR16WCCA-4(71)
• Description: CONN STRAIN RELIEF JR16 4POS
• Manufacturer: Hirose Electric Co Ltd
• Series: JR-Wr

Specifications of JR16WCCA-4(71)

• Accessory Type: Strain Relief
• Shell Size - Insert: 16
• Features: Self Tightening
• Color: Black
• For Use With/related Products: JR-W and RM-W Series Connectors
• For Use With: RM15WTPZA-12S(71) - CONN PLUG CIRC 12POS FREE HANGRM15WTPZA-12P(71) - CONN PLUG CIRC 12POS FREE HANGRM15WTPZA-10S(71) - CONN PLUG CIRC 10POS FREE HANGHR1422 - CONN PLUG WATERPROOF 3POS FEMALEHR1421 - CONN PLUG WATERPROOF 3POS MALEHR1406 - CONN PLUG WATERPROOF 10POS FMALEHR1402 - CONN PLUG WATERPROOF 10POS MALEHR1322 - CONN PLUG WATERPROOF 10POS FMALEHR1321 - CONN PLUG WATERPROOF 7POS FMALEHR1311 - CONN PLUG WATERPROOF 10POS MALEHR1310 - CONN PLUG WATERPROOF 7POS MALE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: *JR16WCCA-4(71); HR1382

144
JR-W Series●IP67 waterproof protected heavy duty metal shell connectors
■Plug assemblies procedure
Table 1(Solder type)
■Work procedure
1.Disassembly of connector
(1)To remove the plug, remove the set screw, fi t a receptacle adaptive to the P shell unit to fi x, and remove he cord tube.
(2)To remove the cord clamp, remove the cord tightening screws.
2.Connection
2.1 Soldering type
(1) Use the cable so that the conductor can be soldered properly into the solder cup with the cable sheath diameter adaptive to each cord
(2) After the terminal treatment of the cable with a size given in Table 1, thread on the ccable the clamp, washer, gasket, cord tube and
(3) Solder to connect the conductors to the terminals of the P shell unit. Shrinkable tube is recommended to be used at the connecting
3.Assembly of connector
(1)Fit the connected P shell unit to the receptacle fi xed with a vice or the like. Torque the cord tube to the level as given in Table3.
(2) Fit the gasket, washer and clamp. Torque the clamp to the level as given in Table3 while preventing the cable from being ratated. And,
(3)Torque the set screw to 0.2 to 0.25 N·m.
(4)Torque the cord tightening screw(two positions) to 0.65 to 0.7 N·m.(Note 4)
Shell size
Note2. keep the size until assembling is completed
Note3. After tightening, check water proof performance before using.
Note4. Check the clamp strenrth before using.
clamp.
coupling in this order and direction as shown above.
part because insulating performance might deteriorate due to solder whiskers or dewing. After connecting, adjust to meet the C size.
(Note2)
Loctite Japan Co Ltd. is recommended to be applied as locking.(Note3)
13
16
21
25
(3)
(3)
(3)
(3)
A
(12)
(14)
(17)
(20)
B
37 or below
39 or below
42 or below
37 or below
C
[Unit:mm]
Table 2
Shell size
13
16
21
25
Tightning torque[Unit:N·m]
2 to 2.5
3 to 3.5
4 to 4.5
5 to 5.5
C