PN5321A3HN/C106;55 NXP Semiconductors, PN5321A3HN/C106;55 Datasheet - Page 6

• Manufacturer Part Number: PN5321A3HN/C106;55
• Description: RF Wireless Misc Combined Analogue Digital IC
• Manufacturer: NXP Semiconductors

Specifications of PN5321A3HN/C106;55

• Rohs Compliant: YES
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 935285223551

Philips Semiconductors
8. Pinning information
Table 3:
9397 750 XXXXX
Short form data sheet
Symbol
DVSS
LOADMOD
TVSS1
TX1
TVDD
TX2
TVSS2
AVDD
VMID
RX
AVSS
AUX1
AUX2
OSCIN
OSCOUT
I0
I1
TESTEN
P35
NC
NC
NC
PVDD
P30
IRQ
RSTOUTN
NSS
MOSI
MISO
SCK
PN532 Pin description
8.1 Pin description
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Type Pad Ref
PWR
O
PWR
O
PWR
O
PWR
PWR
O
I
PWR
O
O
I
O
I
I
I
IO
PWR
IO
O
IO
IO
IO
IO
IO
Voltage
DVDD
TVDD
TVDD
AVDD
AVDD
AVDD
AVDD
AVDD
AVDD
DVDD
DVDD
DVDD
DVDD
PVDD
PVDD
PVDD
PVDD
PVDD
PVDD
PVDD
Description
Digital Ground
Load Modulation output provides digital signal for FeliCa
card operating mode
Transmitter Ground: supplies the output stage of TX1 and TX2
Transmitter 1: delivers the modulated 13.56 MHZ energy carrier
Internal Transmitter power supply: supplies the output stage of TX1 and TX2
Transmitter 2: delivers the modulated 13.56 MHZ energy carrier
Transmitter Ground: supplies the output stage of TX1 and TX2
Internal Analog Power Supply
Internal Reference Voltage: This pin delivers the internal reference voltage.
Receiver Input: Input pin for the reception signal, which is the load modulated
13.56 MHZ energy carrier from the antenna circuit.
Analog Ground
Auxiliary Output: This pin delivers analog and digital test signals.
Auxiliary Output: This pin delivers analog and digital test signals.
Crystal Oscillator Input: input to the inverting amplifier of the oscillator.This
pin is also the input for an externally generated clock (fosc = 27.12 MHZ).
Crystal Oscillator output: Output of the inverting amplifier of the oscillator.
General purpose IO signal
Can be used by the embedded firware to select the used host interface.
General purpose IO signal
Can be used by the embedded firware to select the used host interface.
Test enable pin:
When set to 1 enable the test mode.
When set to 0 reset the TCB and disable the access to the test mode.
General purpose IO signal
Pad power supply
General purpose IO signal. Can be configured to act either as RX line of the
second serial interface or general purpose IO.
In test mode this signal is used as input and output test signal.
Interrupt request: Output to signal an interrupt event to the host (Port 7 bit 0)
Output reset signal. When Low it indicates that the circuit is in reset state.
Not Slave Select .
Master Out Slave In.
Master In Slave Out .
Rev. 1.2 — 31 March 2011
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
PN532/C1
™
and MIFARE
NFC controller
6 of 25
®