2ED300C17-S Infineon Technologies, 2ED300C17-S Datasheet
2ED300C17-S
Specifications of 2ED300C17-S
Available stocks
Related parts for 2ED300C17-S
2ED300C17-S Summary of contents
Page 1
... EiceDRIVER EiceDRIVER 2ED300C17-S 2ED300C17-ST Dual IGBT Driver for Medium and High Power IGBTs Datasheet and Application Note Prepared by : M.Hornkamp Date of publication: 16.05.2003 Approved by: Reg.Nr.064-02 Revision: 3.0 SN: 23925 SN:24816 Status: ™ ™ preliminary eupec GmbH Max-Planck-Straße 5 D-59581 Warstein Author:Michael Hornkamp Tel. +49(0)2902 764-0 Fax +49(0)2902 764-1150 Email: info@eupec ...
Page 2
... The drivers are designed for use with eupec IGBT Modules type IHM, EconoPACK+, 62mm. In case of ulterior use, safe operation cannot be guaranteed. www.eupec.com ™ ™ 2ED300C17-S www.EiceDRIVER.com preliminary Page 2 ...
Page 3
... The Drivers are separated in two temperature classes –25°C for the 2ED300C17-S and –40°C for the 2ED300C17ST. The electrical function and the mechanic dimension are in both version similar. Only if there is a different in the types the 2ED300C17-ST is called. ...
Page 4
... The transformer 2.1 • Safe electrical isolation Protection Class II according to EN50178 3. Application of the 2ED300C17-S 3.1 •Power supply 3.1.1 •Use of the internal over-current shut-down 3.2 •Mode selection 3.3 •Interlock delay times 3.4 • ...
Page 5
... Technical Information EiceDRIVER EiceDRIVER 1.2 Features • Dual channel IGBT driver 2ED300C17-S • For 1200V / 1700V eupec IGBT modules • V monitoring CE sat • “Soft Shut Down” for fault conditions • Save electrical isolation according to EN50178 • Integrated DC-DC SMPS • High peak output current • ...
Page 6
... DD V Voltage DC Converter GND 1.5 Inputs and outputs 2ED300C17 PWM signal inputs for channel A and channel B CA; CB Inputs for external interlock delay time generation for channel A and B in half bridge mode Mode Input for operating mode selection. Direct mode GND; half bridge mode +15V Reset With reset and operating PWM signals the primary fault memory is reset ...
Page 7
... COM A 42 sup Sense Vce sat Gate B 33 Gate B 32 COM COM B 30 sup Sence Vce sat Figure 1.6 Pin configuration of the 2ED300C17-S Pin Label 45 Gate A 44 Gate A 43 COM A 42 COM Sense sat Gate B 32 Gate B 31 COM B 30 COM B ...
Page 8
... Input to Output Min. gate resistor (module internal + external gate resistor) Maximum IGBT gate capacity Voltage slew rate secondary to primary site Operating temperature 2ED300C17-S Operating temperature 2ED300C17-ST Storage temperature Max. switching frequency (T <65° Maximum continue permissible current draw of the dual driver ...
Page 9
... Interlock delay time in half-bridge mode t Coupling capacity primary/secondary C Coupling capacity sec. channel “ Conditions to be defined“ 2) See chapter 2.4 3) See chapter 2.7 4) See chapter 2.3 5) See chapter 2.6 Max. switching frequency: f www.eupec.com ™ ™ 2ED300C17-S Min. Typ. +14 + =+15V P =8W) DC DC/DC +14 +15 0 670 580 50 400 0 – ...
Page 10
... All values by +25°C 4 3,5 3 2,5 2 1 5000 www.eupec.com ™ ™ 2ED300C17-S 1200V IGBT3 10000 15000 Switching frequency in Hz 1700V IGBT3 * Target values 10000 15000 Switching frequency in Hz www.EiceDRIVER.com preliminary * Target values 150A 225A 300A 450A 600A 800A ...
Page 11
... Technical Information EiceDRIVER EiceDRIVER 1.10 Mechanical dimensions 28mm 60,5 mm Clearance distance and creep page Primary/ Clearance distance Secondary/ Secondary Creep page Secondary/ Secondary Max.25mm www.eupec.com ™ ™ 2ED300C17-S 2.95mm RM2.54mm RM2.54mm 2.31mm Secondary 20mm www.EiceDRIVER.com preliminary RM2.54mm 2.95mm 2.31mm >15 mm >6 mm > ...
Page 12
... Safe electrical isolation Protection Class II according to EN50178 The safe isolation between primary and secondary side of the two transformers and the switch mode power supply is the basis for the 2ED300C17-S. Highly insulated coil wires, core insulated ferrites and a special sealing compound (UL94 V-0) are used for this purpose ...
Page 13
... The generated voltages are for the top and bottom channel with +15V primaries each ±16V secondaries. Hence the 2ED300C17-S only requires one external power supply of +15V. The 2ED300C17-S is operated on a stabilized +15V (±1V) supply distinguished between V and V ...
Page 14
... These are the direct mode and the half-bridge mode. • The direct mode: In this mode there is no link between the two channels of the 2ED300C17-S. Both channels IN A and IN B are working independently from each other and may both be turned on at once. The inputs IN A and IN B are switched with +15V PWM signals. ...
Page 15
... EiceDRIVER EiceDRIVER 3.3 Interlock delay times In half-bridge mode the 2ED300C17-S generates a minimal internal interlock delay time between the two channels. This minimal interlock time t adding a capacitance to the two inputs CA and CB this interlock time is extended and adapted to the requirements of the application. The capacitance is externally added between CA and CB to GND (see page 7 – ...
Page 16
... If both PWM signals are “low” for more than 39ms the driver is reset. • Logic outputs The driver core recognizes short circuit current faults of the IGBTs and faults of the supply voltage. Additionally the 2ED300C17-S features an external fault input fault is detected through the V CE sat driver core is immediately turned off ...
Page 17
... EiceDRIVER 3.5 Signal level In both the direct mode and the half-bridge mode the input the 2ED300C17-S controls channel A, and input IN B controls channel B. The inputs feature a Schmitt- Trigger and an active high logic. A high level turns the IGBT on and a low level turns it off ...
Page 18
... With field stop IGBTs only the di/dt turn-on behavior is influenced by the gate resistor. See chapter 3.10 ”sense”. The dv/dt for turn-on and turn-off is still set with the gate resistor. Gate A 45 Gate A 44 COM A 43 COM www.eupec.com ™ ™ 2ED300C17 Figure 3.61 Gate connection R G ein R ...
Page 19
... Technical Information EiceDRIVER EiceDRIVER •Collector connection The 2ED300C17-S is able to measure and evaluate the voltage between collector and emitter of an IGBT. This is used to recognize a short circuit and then shut-down. For the optional function of DVRC or active clamping the connection to the collector is also required. ...
Page 20
... EiceDRIVER 3.7 IGBT short circuit and over-current shut-down with SSD “soft shut down“ A short circuit or over-current is detected by the integrated V 2ED300C17-S (see chapter 3.6). The 2ED300C17-S measures the V IGBT is turned on. If the fault is triggered and the IGBT is turned off via the internal soft shut-down. For eupec IGBT-modules with NPT and FS-technology the soft shut-down reduces the voltage over-shoot by a slower turn-off ...
Page 21
... Technical Information EiceDRIVER EiceDRIVER A comparator inside the 2ED300C17-S compares the voltage at the V reference voltage V . The maximum V ref turn-on of the IGBT the V CE current suppress commutation effects during turning on the IGBT there is the C settable reference curve V ref from 16V to the set voltage level. If the V any time, a fault is tripped and the driver is locked ...
Page 22
... Vce sat Figure 3.7.4 Trigger suppression of the V www.eupec.com ™ ™ 2ED300C17-S measurement ce sat , the 2ED300C17-S uses an RC timing network. This CE CE SAT directly at the input. reff =1µs, the trigger suppression time has to be taken into SD =470R and C =1nF is recommended. VCE VCE ...
Page 23
... IGBT input capacitance C and the Miller capacitance C ies limited 4µs. After this time the output of 2ED300C17-S turns off hard. SD The driver has to be reactivated by a “Reset“ (see chapter 3.4 logic levels). www.eupec.com ™ ...
Page 24
... I C Figure 3.8.2: Short circuit turn-off at 1100V with SSD The short circuit turn-off depicted in Fig. 3.8.2 clearly shows the course of the Gate-Emitter voltage with SSD. www.eupec.com ™ ™ 2ED300C17-S . Hence the gate clamping described GE and ...
Page 25
... EiceDRIVER 3.9 External fault input The 2ED300C17-S features an external fault input E.A and E.B. These are used to set the internal fault memory by a high gate output signal and to trigger a fault. The fault inputs E.A and E.B have an active high logic. Switching level is at 5V, so that a high signal will trigger a fault ...
Page 26
... Figure 3.10.2 Utilization of the “Sense“ input with active clamping The standard application with the 2ED300C17-S is the “Soft Shut Down“. This is a quasi- linear turn-off during fault condition.. The “Soft Shut Down“ has to be adapted to each module type. For this an external resistor R (See chapter 2.8 Short circuit/over-current turn-off with “ ...
Page 27
... IGBT. The outputs +16V and –16V are also used to connect buffer capacitors C prevent voltage drops with high pulse currents. The buffer capacitors should be placed in closest vicinity to the 2ED300C17-S and must always be used. Gate A 45 Gate A 44 ...
Page 28
... Technical Information EiceDRIVER EiceDRIVER www.eupec.com ™ ™ 2ED300C17-S www.EiceDRIVER.com preliminary Page 28 ...
Page 29
... IGBT Chip internal gate resistor g intern R IGBT external gate resistor g extern (Datasheet) R Gate- Emitter resistor GE R Soft Shut Down resistor SSD www.eupec.com ™ ™ 2ED300C17-S R Reference resistor voltage setting VCE CE sat SSD Soft Shut Down t interlock delay time TD t minimum interlock delay time ...
Page 30
... FS450R17KE3 1.67 Ohm FF200R17KE3ENG 2.375 Ohm FF300R17KE3ENG 2.13 Ohm FZ400R17KE3ENG 1.19 Ohm FZ600R17KE3ENG 1.06 Ohm R Table 4.2.2 KE3 1700V modules G intern www.eupec.com ™ ™ 2ED300C17-S G intern FF150R12KE3 G FF200R12KE3 FF300R12KE3 FD200R12KE3 FD300R12KE3 DF200R12KE3 DF300R12KE3 FZ300R12KE3 FZ400R12KE3 FZ600R12KE3 FF600R12KE3 FF800R12KE3 FF1200R12KE3 FZ1200R12KE3 FZ1600R12KE3 ...
Page 31
... FF400R17KF6C_B2 1,53 Ohm FF600R17KF6_B2 1,53 Ohm FF800R17KF6C_B2 1,25 Ohm FZ800R17KF6C_B2 0,76 Ohm FZ1200R17KF6_B2 0,76 Ohm R Table 4.2.4 1700V Modul G intern www.eupec.com ™ ™ 2ED300C17-S BSM200GB120DLC BSM300GB120DLC FF100R12KS4 FF150R12KS4 FF200R12KS4 BSM200GA120DN2 BSM200GA120DN2S BSM300GA120DN2 BSM300GA120DN2S BSM300GA120DN2E3166 BSM400GA120DN2 BSM400GA120DN2S BSM200GA120DLC BSM200GA120DLCS BSM300GA120DLC BSM300GA120DLCS BSM400GA120DLC ...
Page 32
... EiceDRIVER EiceDRIVER EiceDRIVER EiceDRIVER eupec IGBT controlled efficiency DRIVER eupec IGBT controlled efficiency DRIVER 2ED300C17-S For example: www.eupec.com ™ ™ 2ED300C17-S Isolation class funktion isolation S = safety isolation ST= safety isolation/ Traction Voltage class 600V 12 = 1200V 17 = 1700V und 1200V 33 = 3300V 65 = 6500V Driver type: ...