DS90UR906QSQ/NOPB National Semiconductor, DS90UR906QSQ/NOPB Datasheet - Page 24

• Manufacturer Part Number: DS90UR906QSQ/NOPB
• Description: IC SER/DESER 5-65MHZ 24B 60LLP
• Manufacturer: National Semiconductor

Specifications of DS90UR906QSQ/NOPB

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

www.national.com
Functional Description
The DS90UR905Q / DS90UR906Q chipset transmits and re-
ceives 27-bits of data (24-high speed color bits and 3 low
speed video control signals) over a single serial FPD-Link II
pair operating at 140Mbps to 1.82Gbps. The serial stream al-
so contains an embedded clock, video control signals and the
DC-balance information which enhances signal quality and
supports AC coupling. The pair is intended for use with each
other but is backward compatible with previous generations
of FPD-Link II as well.
The Des can attain lock to a data stream without the use of a
separate reference clock source, which greatly simplifies sys-
tem complexity and overall cost. The Des also synchronizes
to the Ser regardless of the data pattern, delivering true au-
tomatic “plug and lock” performance. It can lock to the incom-
ing serial stream without the need of special training patterns
or sync characters. The Des recovers the clock and data by
extracting the embedded clock information, validating and
then deserializing the incoming data stream providing a par-
allel LVCMOS video bus to the display.
The DS90UR905Q / DS90UR906Q chipset can operate in 24-
bit color depth (with VS,HS,DE encoded in the DCA bit) or in
18-bit color depth (with VS, HS, DE encoded in DCA or
mapped into the high-speed data bits). In 18–bit color appli-
cations, the three video signals maybe sent encoded via the
DCA bit (restrictions apply) or sent as “data bits” along with
three additional general purpose signals.
Block Diagrams for the chipset are shown at the beginning of
this datasheet.
Data Transfer
The DS90UR905Q / DS90UR906Q chipset will transmit and
receive a pixel of data in the following format: C1 and C0 rep-
resent the embedded clock in the serial stream. C1 is always
HIGH and C0 is always LOW. b[23:0] contain the scrambled
RGB data. DCB is the DC-Balanced control bit. DCB is used
to minimize the short and long-term DC bias on the signal
lines. This bit determines if the data is unmodified or inverted.
DCA is used to validate data integrity in the embedded data
stream and can also contain encoded control (VS,HS,DE).
Both DCA and DCB coding schemes are generated by the
Ser and decoded by the Des automatically.
trates* the serial stream per PCLK cycle. *Note: The figure
only illustrates the bits but does not actually represent the bit
location as the bits are scrambled and balanced continuously.
Ser & Des OPERATING MODES AND BACKWARD
COMPATIBILITY (CONFIG[1:0])
The DS90UR905Q / DS90UR906Q chipset is also backward
compatible with previous generations of FPD-Link II. Config-
uration modes are provided for backwards compatibility with
the DS90C241 / DS90C124 FPD-Link II Generation 1, and
also the DS90UR241 / DS90UR124 FPD-Link II Generation
2 chipset by setting the respective mode with the CONFIG
[1:0] pins on the Ser or Des as shown in
2. The selection also determine whether the Video Control
FIGURE 19. FPD-Link II Serial Stream (905/906)
Table 1
Figure 19
and
30102037
Table
illus-
24
Signal filter feature is enabled or disabled in Normal mode.
This feature may be controlled by pin or by Register.
VIDEO CONTROL SIGNAL FILTER — Ser and Des
When operating the devices in Normal Mode, the Video Con-
trol Signals (DE, HS, VS) have the following restrictions:
•
•
•
Video Control Signals are defined as low frequency signals
with limited transitions. Glitches of a control signal can cause
a visual display error. This feature allows for the chipset to
validate and filter out any high frequency noise on the control
signals. See
CON
FIG1
CON
FIG1
Normal Mode with Control Signal Filter Enabled:
DE and HS — Only 2 transitions per 130 clock cycles are
transmitted, the transition pulse must be 3 PCLK or longer.
Normal Mode with Control Signal Filter Disabled:
DE and HS — Only 2 transitions per 130 clock cycles are
transmitted, no restriction on minimum transition pulse.
VS — Only 1 transition per 130 clock cycles are
transmitted, minimum pulse width is 130 clock cycles.
H
H
H
H
FIGURE 20. Video Control Signal Filter Waveform
L
L
L
L
CON
FIG0
CON
FIG0
TABLE 2. DS90UR906Q Des Modes
TABLE 1. DS90UR905Q Ser Modes
H
H
H
H
L
L
L
L
Figure
Mode
Normal Mode, Control
Signal Filter disabled
Normal Mode, Control
Signal Filter enabled
Backwards Compatible
GEN2
Backwards Compatible
GEN1
Mode
Normal Mode, Control
Signal Filter disabled
Normal Mode, Control
Signal Filter enabled
Backwards Compatible
GEN2
Backwards Compatible
GEN1
20.
Des Device
DS90UR906Q
DS90UR906Q
DS90UR124,
DS99R124
DS90C124
Ser Device
DS90UR905Q
DS90UR905Q
DS90UR241
DS90C241
30102042