SI3015-KS Silicon Laboratories Inc, SI3015-KS Datasheet - Page 12

• Manufacturer Part Number: SI3015-KS
• Description: IC SI2400 LINE-SIDE DAA 16SOIC
• Manufacturer: Silicon Laboratories Inc
• Type: Enhanced Global Direct Access Arrangementr

Specifications of SI3015-KS

• Package / Case: 16-SOIC (0.154", 3.90mm Width)
• Data Format: V.90
• Interface: Serial
• Voltage - Supply: 3.3 V ~ 5 V
• Mounting Type: Surface Mount
• Product: Modem Module
• Supply Current: 0.3 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Baud Rates: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Contains lead / RoHS non-compliant
• Other names: 336-1094

Si2400
12
Notes:
R7,R8,R15,R16,R17,R19
1. The Si2400 design survives up to 3500 V longitudinal surges without R27, R28, D3, D4, Z4, and Z5. Adding the R27, R28, D3, D4, Z4,
2. For FCC-only designs: C14, C38, C39, R12, R13, R31, and R32 are not required; L1 and L2 may be replaced with a short; R2 may be
3. If the auto answer, ring detect, and caller ID features are not used, R9, R10, C7, C8, C18, and C19 may be removed. In this case, the
4. C22 and C30 may provide an additional improvement in emissions/immunity and/or voice performance, depending on design and
5. Compliance with EN55022 and/or CISPR-22 conducted disturbance tests requires L1, L2, C38, C39, R31, R32, and RV2. See also
6. Several diode bridge configurations are acceptable (suppliers include General Semi., Diodes Inc.).
7. Q4 may require copper on board to meet 1/2 W power requirement. (Contact manufacturer for details.)
8. When L1 and L2 are used, RV2 must be installed, and D1 and D2 must be 400 V.
9. The R7, R8, R15, and R16, R17, R19 resistors may each be replaced with a single resistor of 1.78 kΩ, 3/4 W, ±1%. For FCC-only
10. If the parallel phone detection feature is not used, R25 and R26 may be removed.
11. To ensure compliance with ITU specifications, frequency tolerance must be less than 100 ppm including initial accuracy, 5-year aging,
Z5 enhanced lightning option increases longitudinal surge survival to greater than 6600 V. The isolation capacitors C1, C4, C24, and
C25 must also be rated to greater than the surge voltage. Y-class capacitors are recommended for highest surge survival and are
required for Norway, Sweden, Denmark, and Finland.
±5%; with Z1 rated at 18 V, C5 may be rated at 16 V; also see note 9.
RNG1 and RNG2 pins of the Si3015 should be connected to the IGND pin.
layout. Population option recommended. See "Emissions/Immunity" on page 78.
“EN55022 and CISPR-22 Compliance” in Appendix A.
designs, 1.78 kΩ, 1/16 W, ±5% resistors may be used.
0 to 70°C, and capacitive loading.
Component
R31,R32
R25,R26
R27,R28
R9,R10
Z4,Z5
RV2
R12
R13
Y1
RV1
R2
R11
R18
R24
Z1
R5
R6
U1
U2
11
2
2
8
2
2
1
2,5
3
10
1
9
4.9152 MHz, 20 pF, 50 ppm, 150
Zener Diode, 5.6 V, 1/2 W
Zener Diode, 43 V, 1/2 W
Sidactor, 275 V, 100 A
9.31 kΩ, 1/16 W, ±1%
100 kΩ, 1/16 W, ±1%
120 kΩ, 1/16 W, ±5%
78.7 Ω, 1/16 W, ±1%
10 MΩ, 1/16 W, ±5%
5.36 kΩ, 1/4 W, ±1%
2.2 kΩ, 1/10 W, ±5%
402 Ω, 1/16 W, ±1%
56 kΩ, 1/10 W, ±5%
215 Ω, 1/16 W, ±1%
150 Ω, 1/16 W, ±5%
470 Ω, 1/16 W, ±5%
10 Ω, 1/10 W, ±5%
270 V, MOV
Si2400
Si3015
Value
ESR
Rev. 1.3
Teccor, ST Microelectronics, Microsemi, TI
Vishay, Motorola, Rohm
Vishay, Motorola, Rohm
Venkel, Panasonic
Venkel, Panasonic
Venkel, Panasonic
Venkel, Panasonic
Venkel, Panasonic
Venkel, Panasonic
Venkel, Panasonic
Venkel, Panasonic
Venkel, Panasonic
Venkel, Panasonic
Venkel, Panasonic
Venkel, Panasonic
Venkel, Panasonic
Not Installed
Not Installed
Silicon Labs
Silicon Labs
Suppliers