CC-24K2-IS5 Copeland Communications Inc, CC-24K2-IS5 Datasheet
CC-24K2-IS5
Specifications of CC-24K2-IS5
Related parts for CC-24K2-IS5
CC-24K2-IS5 Summary of contents
Page 1
... Vending & gaming machines Description The CC56K World modem is a compact integrated 56Kbaud ITU-V.90 modem with Socket Modem™ compatibility. The modem features a transformer-less DAA meeting global telephone system requirements, no electro-mechanical components and flexible DSP data pump. The modem is user-configurable to meet virtually all global telecom requirements. The modem supports serial host communications via flexible internal UART. The modem conforms to the industry standard Socket Modem™ ...
Page 2
... Table of Contents Features ...................................................................................................................................1 Applications.............................................................................................................................1 Table of Contents.....................................................................................................................2 Block Diagram.........................................................................................................................3 Detailed Specifications ............................................................................................................6 User-Access Registers (U-Registers)...................................................................................... 36 FCC Compliance ................................................................................................................... 57 CE DECLARATION OF CONFORMITY............................................................................. 58 Revision Information ............................................................................................................. 59 Contact Information............................................................................................................... 60 Legal ..................................................................................................................................... 60 © 2004, Copeland Communications, Inc. Data Sheet Page World modem II Datasheet Rev 1.1 World modem II ...
Page 3
Block Diagram © 2004, Copeland Communications, Inc. Data Sheet Page World modem II Datasheet Rev 1.1 World modem II ...
Page 4
Host Interface The host interface control and data signals are 3.3volts and are 5 volt tolerant. The World modem II modems can be directly connected into 3 volt systems. Connect either pin 57 or pin 61 to 3.3V ...
Page 5
Mechanical Outline Mechanical The modem module 0.062 thick FR-4 PC board. The module has two rows of 2mm pins located 24mm on center. The module is designed to plug into 2 mm sockets with the same 24 ...
Page 6
... Bellcore (US) & ETSI (European) On-hook and off-hook detection Via programmable control registers DTMF & pulse 3.3 V Nominal 3.0V Minimum 3.6V Maximum 35 mA Operating Maximum 130 µA Standby Maximum Commercial 0C-70C FCC part 15 FCC part 68 EN50082-1 CTR-21 Page World modem II Datasheet Rev 1.1 World modem II ...
Page 7
... Notes: 1. Supported on CC-56K2 only 2. Supported on CC-56K2 and CC-33K2 only © 2004, Copeland Communications, Inc. Data Sheet Specification ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V ...
Page 8
... Originate mode Answer mode Output Level Permissive-Switched network Notes: 1. Supported on CC-56K2 only. 2. Supported on CC-56K2 and CC-33K2 only. © 2004, Copeland Communications, Inc. Data Sheet Specification Selectable bits per character ITU-T V.90, V.34, V.32bis, V.32, V.23, V.22bis, V.22, V.21, Bell 212A, and Bell 103 Two-wire full duplex V ...
Page 9
... Line Equalization Connection Options Phone Types Dialing DTMF Output Level Pulse Dial Ratio Ring Cadence Call Progress Monitor Notes: 1. Supported on CC-56K2 only. 2. Supported on CC-56K2 and CC-33K2 only. © 2004, Copeland Communications, Inc. Data Sheet Specifications As specified by ITU-T As specified by ITU-T ± 1800 ± ...
Page 10
... DSP data pump, modem controller, on-chip RAM and ROM, codec, DAA and analog output. The World Modem II accepts standard modem AT commands and provides connect rates up to 56/33.6/14.4 kbps full- duplex over the Public Switched Telephone Network (PSTN). The World modem II features a complete set of modem protocols including all ITU-T standard formats kbps ...
Page 11
Serial Interface The pin out of the serial modem is shown in the figure below. © 2004, Copeland Communications, Inc. Data Sheet Page World modem II Datasheet Rev 1.1 World modem II ...
Page 12
Serial data Autobaud The modem includes an automatic baud rate detection feature that allows the host to start transmitting data at any standard DTE rate from 300 bps to 307.2 kbps. This feature is enabled by default. Flow Control The ...
Page 13
Reset – A hardware reset is provided to reset the modem controller on power- force the modem back to its default settings. This active low signal has an on-board pull up. Leave this pin unconnected if hardware reset ...
Page 14
... WARNING: ONLY connect one (1) of the power supply pins to either 3. models. Connecting both pins 57 and 61 to different power supplies WILL damage the modem and/or the system it is installed in. See CCI Common Socket Interface Specification for more details. © 2004, Copeland Communications, Inc. Data Sheet Page World modem II Datasheet Rev 1 ...
Page 15
... REVERSAL" polarity reversal was detected or "NO POLARITY REVERSAL" polarity reversal was not detected. In each case, the result code is followed by "OK". If the S7 timeout occurs before a busy tone is detected, the modem will report "NO CARRIER". Polarity reversal monitoring begins after the last digit is dialed and ends when the busy tone is detected or S7 timeout occurs ...
Page 16
Basic AT Command Set (Command Defaults in Bold) (Continued) Command In Identification and checksum. I0 Display World Modem chipset version H….etc. I1 Display World Modem firmware revision code (numeric). I3 Display line-side revision code. ...
Page 17
... IO Control 0 (U70). The CID, OCD, PPD, and RI bits are also cleared. :M Write to Serial EEPROM. :P Program RAM write. This command is used to upload firmware supplied by CCI to the modem. Contact CCI for more information. :R User-Access Register Read. This command allows the user to read from user-access registers. The format is " ...
Page 18
Basic AT Command Set (Command Defaults in Bold) (Continued) Command +DR=X Data Compression Reporting. X Mode 0 Disabled 1 Enabled If enabled, the intermediate result code is transmitted at the point after error control negotiation. The format of the result ...
Page 19
... Specifies action taken if an underrun condition occurs after a flag during framed sub-mode. +ESA = A,B,C,E 0 Modem transmits 8-bit HDLC flags on idle. C Specifies action taken if an underrun or overrun condition occurs after a non-flag during +ESA = A,B,C,E,F framed sub-mode. +ESA = 0 Modem transmits abort on underrun in middle of frame. ...
Page 20
Basic AT Command Set (Command Defaults in Bold) (Continued) Command +FCLASS = X Class 1 Mode Enable for V.29 fast connect. X Mode 0 Off 1 Enables support for Class 1 mode for use in the V.29 fast connect mode. ...
Page 21
Basic AT Command Set (Command Defaults in Bold) (Continued) Command +GCI = X Country Settings - Automatically configure all registers for a particular country. X Country 0 Japan 9 Australia A Austria F Belgium 16 Brazil 1B Bulgaria 20 Canada ...
Page 22
Basic AT Command Set (Command Defaults in Bold) (Continued) Command +GCI = X (cont) 82 Norway 87 Paraguay 89 Philippines 8A Poland 8B Portugal 9C Singapore 9F South Africa A0 Spain A5 Sweden A6 Switzerland B4 United Kingdom B5 United ...
Page 23
... Copeland Communications, Inc. Data Sheet Action ITU-T V.21 ITU-T V.22 ITU-T V.22bis ITU-T V.32 (default for CC-14.4K2) ITU-T V.32bis ITU-T V.34 (default for CC-33K2) ITU-T V.90 (default for CC-56K2) Page World modem II World modem II Datasheet Rev 1.1 ...
Page 24
Basic AT Command Set (Command Defaults in Bold) (Continued) Command +PCW = X Controls the action to be taken upon detection of call waiting. X Mode 0 Toggle RI# and collect Type II Caller ID if enabled by +VCID. 1 ...
Page 25
... V.34 with automatic fallback (33.6 kbps to 300 bps) ( default for CC-33K2) &H3 V.34 only (33.6 kbps to 2400 bps) &H4 ITU-T V.32bis with automatic fallback (14.4 kbps to 300 bps) (default for CC-14.4K2) &H5 ITU-T V.32bis only (14.4 kbps to 4800 bps) &H6 ITU-T V.22bis only (2400 bps to 1200 bps) © ...
Page 26
... Initiate ITU-T V.54 (ANALOOP) test. Modulation set by &H AT command. Test loop is through the DSP (CC-14.4K2/CC-33K2/CC-56K2 only). The modem echoes data from TX pin back to RX pin. &T3 Initiate ITU-T V.54 (ANALOOP) test. Modulation set by &H AT command. Test loop is through the DSP, DAA interface section, DAA interface and analog hybrid circuit ...
Page 27
Extended AT& Command Set (Command Defaults in Bold) (Continued) Command &X1 Automatic determination of telephone line type. Result code: WXYZn line supports DTMF dialing line is pulse dial only line supports 20 ...
Page 28
Extended AT% Command Set Command %$ Display AT% command settings. %B Report blacklist. See also S42 register. %Cn Data compression %C0 Disable V.42bis and MNP5 data compression %C1 Enable V.42bis in transmit and receive paths. If MNP is selected (\N2), ...
Page 29
... V.42 (LAPM) reliable mode (or drop call) - Same as \N3 except that the modem drops the call instead of connecting in MNP or wire mode. \N5 V.42 and MNP reliable mode - The modem attempts to connect with V.42 successful, MNP is attempted. If MNP is unsuccessful, the call is dropped. \Pn Parity type will be automatically set in autobaud mode. ...
Page 30
Extended AT\ Command Set (Command Defaults in Bold) (Continued) Command \Tn DTE rate - Change DTE rate. When the modem is configured in autobaud mode (default), \T0 through \T15 will lock the new baud rate and disable autobaud. \T0 300 ...
Page 31
... Result Codes Numeric Meaning Command was successful 0 Link established at 300 bps or higher 1 Incoming ring detected 2 Link dropped 3 Command failed 4 Link established at 1200 5 Dial tone not present 6 Line busy 7 Remote not answering 8 Ringback detected 9 Link established at 2400 10 Link established at 4800 11 Link established at 9600 ...
Page 32
... This message only supported on CC-56K2 and CC-33K2 the only verbal response code that does not follow the <CR><LF> Result Code<CRF><LF> standard. There is no leading <CR><LF> 3. This message is only supported on the CC-56K2 © 2004, Copeland Communications, Inc. Data Sheet ...
Page 33
S-Registers The S command allows reading (Sn?) or writing ( the S-registers. The S-registers store values for functions that typically are rarely changed, such as timers or counters, and the ASCII values of control characters such as carriage ...
Page 34
S Register Definition S-Register (Decimal) 0 Automatic answer - Number of rings the modem must detect before answering a call. 0 disables auto answer. 1 Ring counter. 2 ESC code character. 3 Carriage return character. 4 Linefeed character. 5 Backspace ...
Page 35
S-Register Description (Continued) S-Register (Decimal) 42 Blacklisting - The modem will not dial the same number fore than two times in three minutes. An attempt to dial a 3rd time will result in a "BLACKLISTED" result code. If the blacklist ...
Page 36
... User-Access Registers (U-Registers) The :U AT command is used to write these 16-bit U-Registers and the :R command is used to read them. U- registers are identified by a hexadecimal (hex) address. Register Name U00 DT1A0 DT1 registers set the coefficients for stage 1 of the Dial Tone Detect filter. Default is for ...
Page 37
... User-Access Registers (continued) Register Name U17 BT1A0 BT1 registers set the coefficients fo stage 1 of the Busy Tone Detect filter. Default is for U18 BT1B1 FCC countries. U19 BT1B2 U1A BT1A2 U1B BT1A1 U1C BT2A0 Busy tone detect filter stage 2 biquad coefficients. U1D ...
Page 38
... User-Access Registers (continued) Register Name U33 RMOT Ringback cadence minimum on time in seconds multiplied by 7200. U34 DTWD Window to look for dialtone in seconds multiplied by 1000. U35 DMOT Minimum dialtone on time in seconds multiplied by 7200. U37 PD0 Number of pulses to dial 0. U38 PD1 Number of pulses to dial 1. ...
Page 39
... User-Access Registers (continued) Register Name U4F FHT Flash Hook Time. Time corresponding with "!" or "&" dial modifier that the modem goes on-hook during a flash hook (ms units). U50 LCDN Loop current debounce on time (ms units). U51 LCDF Loop current debounce off time (ms units). ...
Page 40
... User-Access Registers (continued) Register Name U87 SAM U9F SASF UA0 SC0 UA1 SC1 UA2 SC2 UA3 SC3 UA4 SC4 UA5 SC5 UA6 SC6 UA7 SC7 UA8 SC8 UA9 SC9 UAA V29MODE This is a bit-mapped register. © 2004, Copeland Communications, Inc. Data Sheet Description This is a bit-mapped register ...
Page 41
Bit Mapped U-Register Summary Reg. Name Bit Bit Bit U4D MOD1 TOCT NHFP U53 MOD2 REV U62 DAAC1 U63 DAAC3 U65 DAAC4 PWMG PDN U66 DAAC5 U67 ITC1 MIN[1:0] U68 ITC2 U6A ITC4 U6C LVS U6E CK1 ...
Page 42
... Hz Guard Tone Enable Disable Enable. 3 CTE Calling Tone Enable Disable Enable. 2:0 Reserved Read returns 0. © 2004, Copeland Communications, Inc. Data Sheet D11 D10 NHFD CLPD CCAD FTP DSPDM R/W R/W R/W R/W R/W Function Page World modem DGT18 GT55 CTE R/W R/W R/W World modem II Datasheet Rev 1 ...
Page 43
... Automatic Calibration Time set to 426 ms Automatic Calibration Time set to 106 ms Isolation Digital Loopback (see the AT&T commands Loopback occurs beyond the DAA interface, out to and including the analog hybrid circuit Enables digital loopback mode across isolation barrier only. 0 Reserved Must be set to 0. ...
Page 44
U63 DAAC3 Bit D15 D14 D13 D12 Name LCS[7:0] Type Rest settings = 0x0003 Bit Name 15:8 lcs[7:0] Off-Hook Loop Current (1.1 mA/bit). 7:4 ACT[3:0] AC Termination Select. ACT[3:0] 0000 0011 0100 1111 3:0 Reserved Read returns 0x3. U65 DAAC4 ...
Page 45
U66 DAAC5 Bit D15 D14 D13 D12 Name Type Reset settings = 0x0040 Bit Name 15:7 Reserved Read returns 0. 6 FDT Frame Detect. (Typically used only for board-level debug Indicates the modem has not established frame lock. ...
Page 46
U67 ITC1 Bit D15 D14 D13 D12 Name MINI[1:0] Type R/W Reset settings = 0x0008 Bit Name 15:14 Reserved Read returns 0. 13:12 MINI[1:0] Minimum Operational Loop Current. Adjusts the minimum loop current at which the DAA can operate. Increasing ...
Page 47
... When set, the DAA responds automatically to a collapse of the line-derived power supply during a billing tone event. When off-hook, if BTE = 1 and BTD goes high, the dc termination is released (800? presented to the line). If BTE and RIM (U70, bit 9) are set (U70, bit1) interrupt also occurs when BTD goes high. 1 ROV Receive Overload ...
Page 48
U6A ITC4 Bit D15 D14 D13 D12 Name Type Reset settings = N/A Bit Name 15:3 Reserved Do not modify. 2 OVL Overload Detected. This bit has the same function as ROV, but clears itself after the overload has been ...
Page 49
... Parallel phone detected since last off-hook event. Clears on :I read Ring Indicator. Active high bit when the modem is on-hook, indicates ring event has occurred. Clears on :I read. 0 DCD Data Carrier Detect (status). Active high bit indicates carrier detected (equivalent to inverse of DCD# pin). ...
Page 50
U71 IO1 Bit D15 D14 D13 D12 Name Type Reset settings = 0x0000 Bit Name 15:5 Reserved Read returns zero. 4 COMP 0 = Disables compression (PCM mode Enables linear compression. 3:1 Reserved Read returns zero. 0 PRT ...
Page 51
... Delay between when the modem goes off-hook and the off-hook intrusion algorithm begins. Default HOI Hang-Up On Intrusion Modem will not automatically hang up when and off-hook PPD interrupt occurs Modem automatically hangs PPD interrupt. If %Vn command are set, HOI also causes the "LINE IN USE" result code upon PPD interrupt. 10 Reserved Read returns zero ...
Page 52
U78 GEN3 Bit D15 D14 D13 D12 Name IB[1:0] Type Reset settings = 0x0000 Bit Name 15:14 IB[1:0] Intrusion Blocking. Defines the method used to block the off-hook intrusion algorithm from operation after dialing has begun intrusion ...
Page 53
U79 GEN4 Bit D15 D14 D13 D12 Name Type Reset settings = 0x0000 Bit Name 15:5 Reserved Read returns 0. 4:0 LVCS[4:0] Line Voltage Current Sense. Represents either the line voltage, loop current, or on-hook line monitor. On-Hook Voltage Monitor ...
Page 54
... ADD Adaptive Dialing 0 = Disable Enable. Attempt DTMF dial the fall back to pulse dial if unsuccessful. First digit is dialed as DTMF dialtone is still present after two seconds, the modem will redial as pulse dialtone detected after two seconds, the modem will continue to dial as DTMF. 5:3 Reserved Read returns zero ...
Page 55
U7C GENC Bit D15 D14 D13 D12 Name Type Reset settings = 0x0000 Bit Name 15:5 Reserved Read returns zero. 4 RIGPO RI# RI#, follows this bit when RIGPIOEN = 1b. 3:1 Reserved Read returns zero. 0 RIGPOEN 0 = ...
Page 56
... Generate <EM><0x45> ("E" for error) in response to any unrecognized in-band commands. 8 FSMS Framed Sub-Mode Startup 0 = Upon successful connection, enter Transport Sub-Mode. An <EM><FLAG> is required to enter Framed Sub-Mode Upon successful connection, immediately enter Framed Sub-Mode. The first received <EM><ERR> from a successful hunt is transformed into an <EM><flag>. ...
Page 57
... FCC Compliance Certification Number: US:COPMM00BCC-xxK2 AC-REN: 0.0B DC-REN: NA Connectors: RJ11C Compliance: FCC Part 15 and Part 68 © 2004, Copeland Communications, Inc. Data Sheet Page World modem II Datasheet Rev 1.1 World modem II ...
Page 58
... Manufacturer’s Name: Copeland Communications, Inc. Manufacturer’s Address: 440 Colony Place Gahanna, OH, USA 43230 Type of Equipment: Information Technology Equipment Model No.: CC-xxK2 World Modem II Year of Manufacture: 2004 © 2004, Copeland Communications, Inc. Data Sheet 89/336/EEC with Amending Directives: 92/31/EEC, 93/68/EEC, 98/13/EEC Page World modem II Datasheet Rev 1 ...
Page 59
... Revision Information Revision 1.0 to Revision 1.1 Removed unused U registers. Updated PCB layout drawings Added FCC statement © 2004, Copeland Communications, Inc. Data Sheet Page World modem II Datasheet Rev 1.1 World modem II ...
Page 60
... It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Copeland Communications, Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Copeland Communication’ ...