A7MA-206 Omron, A7MA-206 Datasheet

no-image

A7MA-206

Manufacturer Part Number
A7MA-206
Description
SWITCH THUMBWHL GRAY BACK MNT
Manufacturer
Omron
Series
A7MAr
Datasheet

Specifications of A7MA-206

Output Code
BCD
Read Out
0 ~ 9
Actuator Type
Thumbwheel
Mounting Type
Panel Mount, Snap-In (Front)
Termination Style
Card Edge
Component Mounting Area
No
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
A7MA206
Ordering Information
■ SWITCH UNITS
Economical and Reliable Thumbwheel
Switch in Ultra-Small Size
■ ACCESSORIES
Note: 1. When placing your order, please specify the model numbers and quantities of required switch units, end caps, and spacers,
Output Code
06 (binary code)
07 (binary code w/diode provision)
Accessory
End Cap
Spacer
Code
A
B
C
D
E
F
G
Thumbwheel Switch
Output Code
06 (binary code)
07 (binary code w/diode provision)
Gold contacts are employed to provide
maximum contact reliability
Printed circuit board employs epoxy paper
as the base material, with gold plating over
nickel plate for circuit pattern
Switch units can be assembled simply by
fitting the integral hook coupler of each unit
into the mating unit, thus eliminating the
need of nuts and bolts for assembly
(binary code w/+, – display)
(binary code w/+, – display)
2. Switch case, end cap, and spacer are made of polyacetal resin.
3. One of the following alphabetic codes must be filled into the boxed part of the model number to specify a legend to be hot
4. End caps come as a set -- left and right.
respectively. (Note that switch units and accessories are not factory-assembled for shipment.)
stamped on the required spacer.
Legend
Hot stamp
not required
SEC
MIN
H
g
kg
mm
Code
H
J
K
L
Q
T
Legend
cm
m
°C
PCS
x10 SEC
0
Part Number
Front mounting solder terminals
Light gray case
A7MA-206
A7MA-206-PM
A7MA-207
Part Number
For front mounting type switch assembly
Light gray
A7M-2M
A7M-2P■ ■
Back mounting solder terminals
Light gray case
Black case
A7MA-206-1
A7MA-206-PM-1
A7MA-207-1
Black
A7M-2M-1
A7M-2P■ ■
Black case
A7MA-106
A7MA-106-PM
A7MA-107
-1
Front mounting PC board terminals
Light gray case
A7MA-206-P2
A7MA-206-P2-PM
A7MA-207-P2
For back mounting type switch assembly
Light gray
Back mounting PC board terminals
Light gray case
Black case
A7MA-206-P2-1
A7MA-206-P2-PM-1
A7MA-207-P2-1
Black
A7M-1M
A7M-1P■ ■
Black case
A7MA-106-P2
A7MA-106-P2-PM
A7MA-107-P2
A7MA

Related parts for A7MA-206

A7MA-206 Summary of contents

Page 1

... Light gray Black A7M-2M A7M-2M-1 A7M-2P■ ■ A7M-2P■ ■ -1 A7MA Front mounting PC board terminals Light gray case Black case A7MA-206-P2 A7MA-206-P2-1 A7MA-206-P2-PM A7MA-206-P2-PM-1 A7MA-207-P2 A7MA-207-P2-1 Back mounting PC board terminals Light gray case Black case – A7MA-106-P2 – A7MA-106-P2-PM – ...

Page 2

... VAC, 50/60 Hz for 1 minute between each terminal and noncurrent-carrying part 300 g max Hz, 1.5 mm double amplitude 200 m/s 2 (approx -10° to 65°C -20° to 80°C 85% RH max. (at 40°C) 30,000 operations (steps) min. 20,000 operations (steps) min. Approx. 1 1.2 g A7MA-1■ ■ ■ ■P2 No units (n) ( (0.47 (0.71 ...

Page 3

... Panel cutout Note: 1. Unless otherwise specified, a tolerance of ± 0.4 mm applies to all dimensions. 2. Each model number applies to a single switch unit and not to the switch assembly as shown in the drawings. A7MA-2■ ■ ■ ■-P2(-1) Note: Dimension * is 19 for the switch with output code “ ...

Page 4

... A7MA Unit: mm (inch) ■ END CAPS A7M-1M [right] A7M-2M(-1) [right] Note: End caps are attached to each end of the switch assembly and used to secure the switch assembly to a mounting panel. ■ SPACERS A7M-1P■ ■ 4 [left] [left] A7M-2P■ ■ (-1) A7MA ...

Page 5

... OMRON ELECTRONICS, INC. One East Commerce Drive Schaumburg, IL 60173 1-800-55-OMRON Cat. No. GC SW5 4/98 A7MA-■ ■ 06-P2 07 Specifications subject to change without notice. A7MA A7MA-■ ■ 07-P2 OMRON CANADA, INC. 885 Milner Avenue Scarborough, Ontario M1B 5V8 416-286-6465 Printed in the U.S.A. 5 ...

Related keywords