ENW-C9A09N4EF Panasonic - ECG, ENW-C9A09N4EF Datasheet - Page 19

• Manufacturer Part Number: ENW-C9A09N4EF
• Description: MODULE ZIGBEE 2.4GHZ W/SMD PADS
• Manufacturer: Panasonic - ECG
• Series: PAN4555r

Specifications of ENW-C9A09N4EF

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 0dBm
• Sensitivity: -92dBm
• Voltage - Supply: 2 V ~ 3.4 V
• Current - Receiving: 42mA
• Current - Transmitting: 35mA
• Data Interface: PCB, Surface Mount
• Memory Size: 60kB Flash, 4kB RAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ENWC9A09N4EF; P13684TR; PAN4555-SMD

CLASSIFICATION
Einstufung
SUBJECT
Thema
CUSTOMER’S CODE
PAN4555
HIGH FREQUENCY PRODUCTS DIVISION
23.2. NOTES OF INSTALLATION
23.3. NOTES OF USAGE CONDITIONS
PANASONIC ELECTRONIC DEVICES
(5)
(6)
Verarbeitungshinweise
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
Benutzerhinweise
(1)
(2)
(3)
(4)
(5)
(6)
(7)
products' temperature may exceed the maximum allowable.
The supply voltage should not be exceeding or reverse, and should not carry
noise and spike.
Please keep this product away from other high frequency circuits.
Reflow soldering is possible for twice on the condition in chapter 15.
Please set up the temperature at the soldering portion of this product according
to this reflow profile.
Carefully position the products so that their heat will not burn into printed circuit
boards or affect the other components that are susceptible to heat.
Carefully locate these products so that their temperatures will not increase due
to the effects of heat generated by neighboring components.
If a vinyl-covered wire comes into contact with the products, then the cover will
melt and generate toxic gas, damaging the insulation. Never allow contact
between the cover and these products to occur.
This product should not be stressed or vibrated when reflowed.
Please keep the following conditions when you install this product for reparation
by hand soldering.
Please do not wash this product.
Please refer to the recommended pattern when designing a board.
Pressing on parts of the metal cover or fastening objects to the metal cover is
not allowed.
Please take measure against static electricity.
If pulses or other transient loads (a large load applied in a short time) are applied
to the products, then before use, check and evaluate their operation when
assembled on your products.
Please do not use the fallen product.
Please do not put on damage and dirt to the pin , and don't touch the electric
components.
Please follow the condition written in the ratings , about the power supply
instruments applied to this product.
Electrode peeling strength: Do not add pressure of more than 4.9N when
soldered on PCB
Pressing on parts of the metal cover or fastening objects to the metal cover is
not allowed.
These products are intended for general purpose and standard use in general
electronic equipment, such as home appliances, office equipment, information
and communication equipment.
Module Business
EUROPE GmbH
MODEM FOR IEEE802.15.4 (ZIGBEE)
“ZigBee” Modem“ (IEEE802.15.4)
PRODUCT SPECIFICATION
PANASONIC’S CODE
ENWC9A0xxxEF
Produktspezifikation
APPROVED
genehmigt
No.
DS-4555-2400-102
PAGE
Seite
DATE
Datum
CHECKED
geprüft
14.02.2008
19 of 30
DESIGNED
erstellt
REV.
G