ATR2406-DEV-BOARD Atmel, ATR2406-DEV-BOARD Datasheet - Page 6

• Manufacturer Part Number: ATR2406-DEV-BOARD
• Description: BOARD DEVELOPMENT FOR ATR2406
• Manufacturer: Atmel
• Series: Smart RFr
• Type: Transceiver, ISMr

Specifications of ATR2406-DEV-BOARD

• Frequency: 2.4GHz
• Wireless Frequency: 2.4 GHz
• Interface Type: SPI
• Modulation: GFSK
• Operating Voltage: 2.9 V to 3.6 V
• Antenna: F-Antenna, SMA
• Operating Temperature Range: - 10 C to + 60 C
• For Use With/related Products: ATR2406
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

6. Electrical Characteristics
V
6
Notes:
S
No.
1.1
1.2
1.3
1.4
1.5
1.6
1.7
2.1
2.2
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
4.1
4.2
4.3
4.4
= 3.6V with AUX regulator, T
1
2
3
4
Parameters
Supply
Supply voltage
Supply voltage
RX supply current
TX supply current
Battery lifetime of a remote
control application using an
AVR
Supply current in power-down
mode
Supply current in power-down
mode
Voltage Regulator
AUX regulator
VCO regulator
Transmitter Part
TX data rate
Output power
TX data filter clock
Frequency deviation
Frequency deviation scaling
Frequency drift
Harmonics
Spurious emissions
30 – 1000 MHz
1 – 12.75 GHz
1.8 – 1.9 GHz
5.15 – 5.3 GHz
Ramp Generator, Pin 21
Minimum output voltage
Maximum output voltage
Rise time
Fall time
1. Measured and guaranteed only on the Atmel
2. Timing is determined by external loop filter characteristics. Faster timing can be achieved by modification of the loop filter.
3. The Gaussian filter control setting (GFCS) is used to compensate production tolerances by tuning the modulation deviation
4. Burst mode with 0.9% duty cycle
ATR2406
®
quency (Smart RF) firmware. Conducted measured.
For further information refer to the application notes.
in production to the nominal value of 400 kHz.
amb
= 25°C, unless otherwise specified
(3)
Test Conditions
With AUX regulator
Without AUX regulator
CW mode (peak current)
Burst mode at 10 Kbits/s
CW mode (peak current)
Burst mode at 10 Kbits/s
See
Calculations for a Remote Control”
on page 20
With AUX regulator
PU_TRX = 0; PU_REG = 0
Without AUX regulator
PU_TRX = 0; PU_REG = 0
9 taps in filter
To be tuned by GFCS bits
GFFM = GF
(Refer to bus protocol D9 to D11)
With standard loop filter and slot
length of 1400 µs (Refer to the
application note “ATR2406 Loop
Filter and Data Rates”)
BW = 100 kHz
BW = 100 kHz
TX_ON = low
Refer to bus protocol D12 to D13
Section 10. “Appendix: Current
FM_nom
(1)
(1)
®
evaluation board, including microstrip filter, balun, and Smart Radio Fre-
GFCS
(4)
(4)
VREG_VCO
GF
Symbol
VREG
f
fo (drift)
GFCS
TXFCLK
PTX
V
V
FM_nom
V
V
I
I
I
I
I
I
max
t
t
min
S
S
S
S
S
S
r
f
S
S
Min.
3.2
2.9
1.1
60
72/144/288/576/1152
10.368/13.824
±400
Typ.
625
500
3.6
3.0
< 1
< 1
3.0
2.7
0.7
57
42
4
5
5
–41.2
Max.
130
±40
–57
–57
–57
–57
4.6
3.6
1.9
4779N–ISM–12/08
kBits/s
dBm
MHz
dBm
dBm
dBm
dBm
dBm
Unit
kHz
kHz
mA
mA
µA
µA
µA
µA
µs
µs
%
V
V
V
V
V
V