829144A00050P Crouzet USA, 829144A00050P Datasheet

Page 1

... Stepper Motors Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/111 ...

Page 2

... Stepper motors selection guide Gearboxes Direct motors Absorbed Holding torque Power (mN.m) (w) 2 phases 4 phases 7 180 155 12.5 300 240 Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/112 Torque max (N m) Gearbox type ...

Page 3

Products and specifications subject to change without notice. Order/Technical ...

Page 4

... Direct drive stepper motors ➜ 7.5° 5 Watts ■ 48 steps/revolution (7.5°) ■ Absorbed power : 5 W ■ phase versions available Specifications Type Part numbers Plastic bearing Sintered bronze bearing General characteristics Resistance per phase (Ω) Inductance per phase (mH) Current per phase (A) Holding torque (mN ...

Page 5

Curves Inertia of measuring chain : 1.5 g. constant voltage controller with Rs (resistance in series constant voltage controller with Rs (resistance in series motor c = constant voltage controller with ...

Page 6

... Direct drive stepper motors ➜ 7.5° 5 Watts ■ 48 steps/revolution (7.5°) ■ Absorbed power : 5 W ■ phase versions available Specifications Type Electronic controller used Bearings Sintered bronze Plastic General characteristics Electronic controller used Resistance per phase (Ω) Inductance per phase (mH) Current per phase (A) Holding torque (mN ...

Page 7

Curves Inertia of measuring chain : 1.5 g. constant voltage controller with Rs (resistance in series constant voltage controller with Rs (resistance in series motor c = constant voltage controller with ...

Page 8

... Direct drive stepper motors ➜ 15° 5 Watts ■ 24 steps/revolution (15°) ■ Absorbed power : 5 W ■ phase versions available Specifications Type Number of phases Part numbers General characteristics Electronic controller used Resistance per phase (Ω) Inductance per phase (mH) Current per phase (A) Holding torque (mN.m) ...

Page 9

Curves Measurement conditions 2 phase : L 297 298 SGS constant voltage supply board, 5 motor terminals, 2 phases energized, full steps, inertia of measuring system 4.53 g.cm Measurement conditions 4 phase : 89 990 101 constant voltage ...

Page 10

... Direct drive stepper motors ➜ 7.5° 10 Watts ■ 48 steps/revolution (7.5°) ■ Absorbed power : 10 W ■ phase versions available Specifications Type Number of phases Electronic controller used Resistance per Current per Voltage at motor phase (Ω) phase (A) terminals (V) 9 0.75 6.6 22.3 ...

Page 11

Curves Inertia of measuring chain : 3.4 g. constant voltage controller with Rs (resistance in series constant voltage controller with Rs (resistance in series motor c = constant voltage controller with ...

Page 12

... Direct drive stepper motors ➜ 7.5° 7.5 Watts ■ 48 steps/revolution (7.5°) ■ Absorbed power : 7.5 W ■ phase versions available Specifications Type Number of phases Electronic controller used Resistance per Current per Voltage at motor phase (Ω) phase (A) terminals (V) 10.7 0.59 6 ...

Page 13

Curves Inertia of measuring chain : 2.2 g. constant voltage controller with Rs (resistance in series constant voltage controller with Rs (resistance in series motor c = constant voltage controller with ...

Page 14

... Direct drive stepper motors ➜ 7.5° 12.5 Watts ■ 48 steps/revolution (7.5°) ■ Absorbed power : 12.5 W ■ phase versions available Specifications Type Number of phases Electronic controller used Resistance per Current per Voltage at motor phase (Ω) phase (A) terminals (V) 5.2 1.1 5.7 26 ...

Page 15

Curves Inertia of measuring chain : 20.5 g. constant voltage controller with Rs (resistance in series constant voltage controller with Rs (resistance in series motor c = constant voltage controller with ...

Page 16

... Geared stepper motors ➜ 0 and 7.5 Watts ■ Mechanical strength: 0.5 Nm ■ Various ratios available ■ phase versions available Specifications 7.5 Watts Type 82 924 0 Number of phases 2 Ratios 10 82 924 020 20 82 924 022 25 50 100 250 500 General characteristics Stepper motor ...

Page 17

Dimensions 82 924 fixing holes Ø 3.2 C 3.5 across flat D ← ) (pushed-in shaft 82 914 914 fixing holes Ø 3.2 C 3.5 across flat 82 914 0 = ...

Page 18

... Geared stepper motors ➜ and 7.5 Watts ■ Mechanical strength : 2 Nm ■ Various ratios available ■ phase versions available Specifications Type Number of phases Ratios 25 50 100 250 General characteristics Stepper motor / Number of phases Gearbox Step angle ( o ) Maximum permitted torque from gearmotor under continuous conditions (N ...

Page 19

Dimensions 82 929 fixing holes Ø 3 across flat D 3 mounting bosses Ø 6.8 at 120° on radius = 19.5 3 holes M3 depth 4.5 82 919 919 ...

Page 20

... Geared stepper motors ➜ and 7.5 Watts ■ Mechanical strength : 5 Nm ■ Various ratios available ■ phase versions available Specifications Number of phases Ratios 12.5 25 31.25 41.66 62.5 83.33 125 250 500 750 2500 General characteristics Motor Gearbox Maximum permitted torque from gearmotor under continuous conditions (N ...

Page 21

Dimensions 80 917 927 holes M4 depth 12 C across flat D ← ) (pushed-in shaft 80 917 58 Ø 22.3 mm ...

Page 22

... Geared stepper motors ➜ 2.5 and 3.5 Watts ■ Mechanical strength ■ Various ratios available ■ phase versions available Specifications 2.5 Watts Type 80 913 0 Ratios 150 187.5 300 375 600 750 1200 2250 2400 3600 General characteristics Motor 82 910 0 Gearbox 81 023 0 ...

Page 23

Dimensions 80 913 0 0.1 80 923 0 933 0.1 60 Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / ...

Page 24

... Geared stepper motors ➜ 12.5 Watts ■ Mechanical strength : 5 Nm ■ Various ratios available ■ phase versions available Specifications Type Number of phases Ratios 12.5 25 31.25 41.66 62.5 83.33 125 250 500 750 2500 General characteristics Motor Gearbox Maximum permitted torque from gearmotor under continuous conditions (N ...

Page 25

Dimensions 80 947 holes M4 depth 12 C across flat D ← ) (pushed-in shaft 80 947 76 Ø Options Shaft 79 206 ...