129-0701-202 Emerson Network Power, 129-0701-202 Datasheet - Page 258

• Manufacturer Part Number: 129-0701-202
• Description: CONN JACK TEST SHIELD VERTICAL T
• Manufacturer: Emerson Network Power
• Type: Tip Jackr

Specifications of 129-0701-202

• Gender: Female
• Plug/mating Plug Diameter: Standard
• Mounting Type: Through Hole, Vertical
• Termination: Solder
• Insulation: Non-Insulated
• Contact Finish: Gold
• Contact Material: Beryllium Copper
• Body Material: TFE Fluorocarbon
• Operating Temperature: -65°C ~ 85°C
• Color: Silver
• Contact Plating: Gold
• Equipment Type: Shielded Test Jack
• Voltage Rating: 2000 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Color: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 1290701202; J570

258
Assembly Instructions
INCHES (MILLIMETERS) • CUSTOMER DRAWINGS AVAILABLE ON REQUEST
Mini-UHF Straight Crimp Type Plugs
for Flexible Cable
MINI-UHF-1B
MINI-UHF-16
MINI-UHF-17
MINI-UHF-1
MINI-UHF-2
PART NO.
Connectivity Solutions
RG-450, Proflex
RG-58 Black
RG-59, 62
CABLE
RG-8X
RG-58
.044 (1.11)
.044 (1.11)
.034 (0.86)
.055 (1.40)
.065 (1.65)
CONTACT
I.D.
Tel: [phone]
.126 (3.20)
.126 (3.20)
.173 (4.40)
.173 (4.40)
.173 (4.40)
BODY
I.D.
.206 (5.23)
.206 (5.23)
.261 (6.63)
.261 (6.63)
.261 (6.63)
FERRULE
•
I.D.
Fax: [phone]
(BRAID HEX) CRIMP HEX
.210 (5.33)
.210 (5.33)
.255 (6.48)
.255 (6.48)
.255 (6.48)
CRIMP
•
.060 (1.52)
.060 (1.52)
.060 (1.52)
.060 (1.52)
.060 (1.52)
CONTACT
www.EmersonNetworkPower.com/connectivity
RECOMMENDED
1. Identify connector parts. (4 piece parts)
2. Slide heat shrink (as applicable) and crimp
3. Assemble contact onto cable as shown.
4. Slide coupling nut onto the connector
5. Flare braid and slide body assembly over
CRIMP TOOL
24-8860P
24-8860P
24-8860P
24-8860P
24-8860P
sleeve onto jacket of cable. Strip cable to
dimensions shown. Do not nick braid or
center conductor. Tin center conductor if
contact will be solder attached. Do not tin
center conductor if contact is to be crimp
attached. A wire stripper of correct size is
recommended for this step.
Solder Attachment: Solder contact to
center conductor through hole using a
minimum amount of solder for a good joint.
Crimp Attachment (where applicable):
Crimp contact to center conductor using
recommended crimp tool.
body.
contact and under braid as shown. Then
seat body assembly firmly onto contact
until a gentle snap is felt indicating the
contact is in place. The cable may have to
be held in a clamping fixture. Arrange braid
uniformly around crimp stem. Slide crimp
sleeve forward and crimp using recom-
mended crimp tool. Slide heat shrink
forward and shrink (as applicable).