OP162HRU-REEL Analog Devices Inc, OP162HRU-REEL Datasheet - Page 15

• Manufacturer Part Number: OP162HRU-REEL
• Description: IC OPAMP GP R-R 15MHZ LN 8TSSOP
• Manufacturer: Analog Devices Inc

Specifications of OP162HRU-REEL

• Rohs Status: RoHS non-compliant
• Amplifier Type: General Purpose
• Number Of Circuits: 1
• Output Type: Rail-to-Rail
• Slew Rate: 13 V/µs
• Gain Bandwidth Product: 15MHz
• Current - Input Bias: 260nA
• Voltage - Input Offset: 25µV
• Current - Supply: 650µA
• Current - Output / Channel: 30mA
• Voltage - Supply, Single/dual (±): 2.7 V ~ 12 V, ±1.35 V ~ 6 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-TSSOP
• -3db Bandwidth: -

The network operates in parallel with the load capacitor, C
and provides compensation for the added phase lag. The actual
values of the network resistor and capacitor are empirically
determined to minimize overshoot and maximize unity-gain
bandwidth. Table 6 shows a few sample snubber networks for
large load capacitors.
Table 6. Snubber Networks for Large Capacitive Loads
C
< 300 pF
500 pF
1 nF
10 nF
Higher load capacitance will reduce the unity-gain bandwidth
of the device. Figure 43 shows unity-gain bandwidth vs.
capacitive load. The snubber network does not provide any
increase in bandwidth, but it substantially reduces ringing and
overshoot, as shown between Figure 41 and Figure 42.
TOTAL HARMONIC DISTORTION AND CROSSTALK
The OPx62 device family offers low total harmonic distortion
making it an excellent choice for audio applications. Figure 44
shows a graph of THD plus noise figures at 0.001% for the
OP462.
LOAD
100
0%
90
10
10
Figure 42. A Photo of a Nice Square Wave at the Output
10pF
9
8
7
6
5
4
3
2
1
0
Figure 43. Unity-Gain Bandwidth vs. C
50mV
100pF
R
140 Ω
100 Ω
80 Ω
10 Ω
X
C
LOAD
V
A
C
R
WITH SNUBBER:
1nF
R
C
1 µ s
S
V
L
L


X
X
= 5V
= 1
= 300pF
= 10k Ω
= 140 Ω
= 10nF
LOAD
C
10 nF
10 nF
10 nF
47 nF
X
10nF
L
,
Rev. F | Page 15 of 20
Figure 45 shows the worst case crosstalk between two amplifiers
in the OP462. A 1 V rms signal is applied to one amplifier while
measuring the output of an adjacent amplifier. Both amplifiers
are configured for unity gain and supplied with ±2.5 V.
PCB LAYOUT CONSIDERATIONS
Because the OP162/OP262/OP462 can provide gains at high
frequency, careful attention to board layout and component
selection is recommended. As with any high speed application,
a good ground plane is essential to achieve the optimum
performance. This can significantly reduce the undesirable
effects of ground loops and I × R losses by providing a low
impedance reference point. Best results are obtained with a
multilayer board design with one layer assigned to ground
plane.
Use chip capacitors for supply bypassing, with one end of the
capacitor connected to the ground plane and the other end
connected within 1/8 inch of each power pin. An additional
large tantalum electrolytic capacitor (4.7 µF to 10 µF) should be
connected in parallel. This capacitor provides current for fast,
large-signal changes at the device’s output; therefore, it does not
need to be placed as close to the supply pins.
0.0001
0.010
0.001
–100
–110
–120
–130
–140
–40
–50
–60
–70
–80
–90
20
20
V
A
V
R
BANDWIDTH:
<10Hz TO 22kHz
A
V
R
V
S
IN
IN
S
V
L
V
L
= ±2.5V
= 1
= 10kΩ
= 1
= 10kΩ
= ±2.5V
= 1.0V rms
= 1.0V rms
(0dBV)
Figure 45. Crosstalk vs. Frequency
Figure 44. THD + N vs. Frequency

100
100
FREQUENCY (Hz)
FREQUENCY (Hz)
OP162/OP262/OP462
1k
1k
10k 20k
10k 20k