AD620ARZ Analog Devices Inc, AD620ARZ Datasheet - Page 17

• Manufacturer Part Number: AD620ARZ
• Description: IC AMP INST LP LN 18MA 8SOIC
• Manufacturer: Analog Devices Inc
• Type: Instrumentation Ampr

Specifications of AD620ARZ

• Design Resources: Low Cost Programmable Gain Instrumentation Amplifier Circuit Using ADG1611 and AD620 (CN0146)
• Amplifier Type: Instrumentation
• Number Of Circuits: 1
• Slew Rate: 1.2 V/µs
• -3db Bandwidth: 1MHz
• Current - Input Bias: 500pA
• Voltage - Input Offset: 30µV
• Current - Supply: 900µA
• Current - Output / Channel: 18mA
• Voltage - Supply, Single/dual (±): 4.6 V ~ 36 V, ±2.3 V ~ 18 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Number Of Channels: 1
• Number Of Elements: 1
• Power Supply Requirement: Dual
• Common Mode Rejection Ratio: 73dB
• Input Resistance: 10000@±15VMohm
• Input Offset Voltage: 0.125@±15VmV
• Input Bias Current: 0.002@±15VnA
• Single Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (typ): 15V
• Power Dissipation: 650mW
• Rail/rail I/o Type: No
• Single Supply Voltage (min): Not RequiredV
• Single Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (min): ±2.3V
• Dual Supply Voltage (max): ±18V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: SOIC N
• Bandwidth: 12 kHz
• Current, Input Bias: 0.5 nA
• Current, Input Offset: 0.3 nA
• Current, Supply: 1.3 mA
• Impedance, Thermal: 155 °C/W
• Temperature, Operating, Range: -40 to +85 °C
• Voltage, Gain: 1-10000 V/V
• Voltage, Input: -13.1 to +13.8 V
• Voltage, Input Offset: 30 μV
• Voltage, Noise: 9 nV/sqrt Hz (Input), 72 nV/sqrt Hz (Output)
• Voltage, Output Swing: -13.9 to +13.8 V
• Voltage, Supply: ±2.3 to ±18 V
• No. Of Amplifiers: 1
• Gain Db Min: 1dB
• Amplifier Output: Single Ended
• Cmrr: 130dB
• Supply Voltage Range: ± 2.3V To ± 18V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• Gain Bandwidth Product: -
• Lead Free Status / Rohs Status: Compliant

COMMON-MODE REJECTION
Instrumentation amplifiers, such as the AD620, offer high
CMR, which is a measure of the change in output voltage when
both inputs are changed by equal amounts. These specifications
are usually given for a full-range input voltage change and a
specified source imbalance.
For optimal CMR, the reference terminal should be tied to a
low impedance point, and differences in capacitance and
resistance should be kept to a minimum between the two
inputs. In many applications, shielded cables are used to
minimize noise; for best CMR over frequency, the shield
should be properly driven. Figure 44 and Figure 45 show active
data guards that are configured to improve ac common-mode
rejections by “bootstrapping” the capacitances of input cable
shields, thus minimizing the capacitance mismatch between the
inputs.
Figure 43. Circuit to Attenuate RF Interference
R
R
C
C
C
C
D
C
0.1µ F
499Ω
0.1µ F
+IN
–IN
+15V
–15V
+
–
AD620
REF
V
1 µ F
1 µ F
OUT
0
0
Rev. G | Page 17 of 20
GROUNDING
Since the AD620 output voltage is developed with respect to the
potential on the reference terminal, it can solve many
grounding problems by simply tying the REF pin to the
appropriate “local ground. ”
To isolate low level analog signals from a noisy digital
environment, many data-acquisition components have separate
analog and digital ground pins (Figure 46). It would be
convenient to use a single ground line; however, current
through ground wires and PC runs of the circuit card can cause
hundreds of millivolts of error. Therefore, separate ground
returns should be provided to minimize the current flow from
the sensitive points to the system ground. These ground returns
must be tied together at some point, usually best at the ADC
package shown in Figure 46.
100 Ω
100 Ω
AD620
AD648
100Ω
0.1 µ F
Figure 45. Common-Mode Shield Driver
– INPUT
+ INPUT
Figure 46. Basic Grounding Practice
Figure 44. Differential Shield Driver
AD548
+ INPUT
– INPUT
+15V C –15V
ANALOG P.S.
–V
AD585
0.1 µ F
S
S/H
R
G
R
R
2
2
G
G
AD620
1
µ
+V
–V
AD620
F 1
S
S
AD574A
µ
+V
–V
F
ADC
DIGITAL P.S.
S
S
REFERENCE
C
1
µ
+5V
+
F
REFERENCE
AD620
DIGITAL
DATA
OUTPUT
V
V
OUT
OUT