STM32F103C8T6TR STMicroelectronics, STM32F103C8T6TR Datasheet - Page 36

• Manufacturer Part Number: STM32F103C8T6TR
• Description: MCU ARM 64KB FLASH MEM 48-LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103C8T6TR

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 37
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 20K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• For Use With: 497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32497-8511 - KIT STARTER FOR STM32 512K FLASH497-6438 - BOARD EVALUTION FOR STM32 512K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Electrical characteristics
5.3
5.3.1
36/96
Table 7.
1. All main power (V
2. I
3. Negative injection disturbs the analog performance of the device. See note in
4. When several inputs are submitted to a current injection, the maximum I
Table 8.
Operating conditions
General operating conditions
Table 9.
I
Symbol
V
INJ(PIN)
I
supply, in the permitted range.
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
characteristics.
positive and negative injected currents (instantaneous values). These results are based on
characterization with I
f
f
INJ(PIN)
f
PCLK1
PCLK2
V
DDA
HCLK
Symbol
V
INJ(PIN)
BAT
DD
Symbol
I
I
VDD
VSS
I
T
IO
(1)
STG
T
J
(2)(3)
must never be exceeded. This is implicitly insured if V
(2)
Current characteristics
Thermal characteristics
General operating conditions
Internal AHB clock frequency
Internal APB1 clock frequency
Internal APB2 clock frequency
Standard operating voltage
Analog operating voltage
(ADC not used)
Analog operating voltage
(ADC used)
Backup operating voltage
Total current into V
Total current out of V
Output current sunk by any I/O and control pin
Output current source by any I/Os and control pin
Injected current on NRST pin
Injected current on HSE OSC_IN and LSE OSC_IN pins
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
DD
, V
Storage temperature range
Maximum junction temperature
DDA
INJ(PIN)
Parameter
IN
> V
) and ground (V
DD
maximum current injection on four I/O port pins of the device.
while a negative injection is induced by V
Doc ID 13587 Rev 12
DD
SS
/V
Ratings
SS
DDA
ground lines (sink)
, V
Ratings
SSA
power lines (source)
Must be the same potential
as V
) pins must always be connected to the external power
(4)
DD
(2)
Conditions
IN
maximum is respected. If V
(1)
STM32F103x8, STM32F103xB
(1)
INJ(PIN)
IN
INJ(PIN)
(4)
< V
Section 5.3.17: 12-bit ADC
–65 to +150
is the absolute sum of the
SS
.
value. A positive
Value
150
Min
2.4
1.8
0
0
0
2
2
Max.
 25
± 25
150
150
± 5
± 5
± 5
25
IN
Max
maximum
3.6
3.6
3.6
3.6
72
36
72
Unit
Unit
MHz
°C
°C
Unit
mA
V
V
V