STM8L152C6T6 STMicroelectronics, STM8L152C6T6 Datasheet - Page 61

• Manufacturer Part Number: STM8L152C6T6
• Description: IC MCU 8BIT 32KB FLASH 48LQFP
• Manufacturer: STMicroelectronics
• Series: STM8L EnergyLiter

Specifications of STM8L152C6T6

• Core Processor: STM8
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, IR, LCD, POR, PWM, WDT
• Number Of I /o: 41
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 25x12b, D/A 1x12
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Processor Series: STM8L15x
• Core: STM8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 41
• Number Of Timers: 5
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWSTM8
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 25 Channel
• On-chip Dac: 12 bit, 1 Channel
• For Use With: 497-10594 - DEM FOR STM8L15X LOW PWR MODES497-10590 - BOARD EVAL FOR STM8L152C6
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-10512

STM8L151xx, STM8L152xx
9.1.5
9.2
Pin input voltage
The input voltage measurement on a pin of the device is described in
Figure 11. Pin input voltage
Absolute maximum ratings
Stresses above those listed as “absolute maximum ratings” may cause permanent damage
to the device. This is a stress rating only and functional operation of the device under these
conditions is not implied. Exposure to maximum rating conditions for extended periods may
affect device reliability.
Table 14.
1. All power (V
2. Positive injection is not possible on these I/Os. V
3. I
external power supply.
never be exceeded. A negative injection is induced by V
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
INJ(PIN)
V
Symbol
DD
V
V
ESD
- V
IN
must never be exceeded. This is implicitly insured if V
SS
Voltage characteristics
DD1
, V
DD2
External supply voltage (including V
and V
Input voltage on true open-drain pins
(PC0 and PC1)
Input voltage on FT pins (PA7 and
PE0)
Input voltage on any other pin
Electrostatic discharge voltage
, V
IN
(2)
DDA
DD2
>V
) and ground (V
DD
)
(1)
while a negative injection is induced by V
Doc ID 15962 Rev 5
(2)
Ratings
V
IN
SS1
, V
IN
SS2
maximum must always be respected. I
(3)
, V
IN
SSA
STM8L PIN
<V
DDA
) pins must always be connected to the
SS
IN
.
maximum is respected. If V
ratings (electrical sensitivity)
see
V
V
V
SS
SS
SS
- 0.3
Min
- 0.3
- 0.3
- 0.3
IN
Absolute maximum
on page 108
<V
INJ(PIN)
SS
.
Electrical parameters
value. A positive
Figure
V
V
DD
DD
Max
4.0
4.0
+ 4.0
+ 4.0
INJ(PIN)
IN
11.
maximum
must
Unit
61/122
V