PIC16C74B-20E/P Microchip Technology, PIC16C74B-20E/P Datasheet - Page 121
![IC MCU OTP 4KX14 A/D PWM 40DIP](/photos/6/61/66192/150-40-dip_sml.jpg)
PIC16C74B-20E/P
Manufacturer Part Number
PIC16C74B-20E/P
Description
IC MCU OTP 4KX14 A/D PWM 40DIP
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16F818-ISO.pdf
(6 pages)
3.PIC16C63A-04SP.pdf
(184 pages)
4.PIC16C63A-04SP.pdf
(10 pages)
5.PIC16C63A-04SP.pdf
(10 pages)
Specifications of PIC16C74B-20E/P
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
33
Program Memory Size
7KB (4K x 14)
Program Memory Type
OTP
Ram Size
192 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 5.5 V
Data Converters
A/D 8x8b
Oscillator Type
External
Operating Temperature
-40°C ~ 125°C
Package / Case
40-DIP (0.600", 15.24mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16C74B-20E/PQ
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
PIC16C74B-20E/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Note 1: This is the limit to which V
PIC16LC63A/65B/73B/74B-04
‡
‡
D100
D101
D102
Param
PIC16C63A/65B/73B/74B-04
PIC16C6A/65B/73B/74B-20
* These parameters are characterized but not tested.
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and
‡ When specification values of standard devices differ from those of extended voltage devices, they are shown in gray.
2000 Microchip Technology Inc.
No.
are not tested.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is mea-
4: For RC osc mode, current through R
5: Timer1 oscillator (when enabled) adds approximately 20 A to the specification. This value is from character-
6: The
7: When BOR is enabled, the device will operate correctly until the V
8: In RC oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
9: The leakage current on the MCLR/V
10: Negative current is defined as current sourced by the pin.
C
loading and switching rate, oscillator type, internal code execution pattern and temperature also have an impact
on the current consumption. The test conditions for all I
OSC1 = external square wave, from rail to rail; all I/O pins tri-stated, pulled to V
MCLR = V
sured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to V
the formula Ir = V
ization and is for design guidance only. This is not tested.
added to the base I
PICmicro device be driven with external clock in RC mode.
els represent normal operating conditions. Higher leakage current may be measured at different input voltages.
Sym
C
OSC2
Cb
IO
current is the additional current consumed when this peripheral is enabled. This current should be
Capacitive Loading
Specs on
Output Pins
OSC2 pin
All I/O pins and OSC2
(in RC mode)
SCL, SDA
(in I
DD
Characteristic
2
C mode)
; WDT enabled/disabled as specified.
DD
DD
/2R
or I
EXT
PD
DD
(mA) with R
measurement.
can be lowered without losing RAM data.
Standard Operating Conditions (unless otherwise stated)
Operating temperature
Standard Operating Conditions (unless otherwise stated)
Operating temperature
Min
PP
–
–
–
EXT
pin is strongly dependent on the applied voltage level. The specified lev-
EXT
is not included. The current through the resistor can be estimated by
Typ†
PIC16C63A/65B/73B/74B
in kOhm.
–
–
–
Max
400
15
50
DD
-40°C
-40°C
-40°C
measurements in active operation mode are:
Units
0°C
0°C
pF
pF
pF
In XT, HS and LP modes when external
clock is used to drive OSC1
BOR
T
T
T
T
T
A
A
A
A
A
voltage trip point is reached.
+125°C
+70°C
+85°C
+70°C
+85°C
DD
Conditions
,
for commercial
for industrial
for commercial
for industrial
for extended
DD
DS30605C-page 121
and V
SS
.