C8051F563-IQ Silicon Laboratories Inc, C8051F563-IQ Datasheet - Page 237

• Manufacturer Part Number: C8051F563-IQ
• Description: IC 8051 MCU 32K FLASH 32-QFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F56xr

Specifications of C8051F563-IQ

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 32-QFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.25 V
• Data Converters: A/D 25x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: C8051F5x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2304 B
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 25
• Operating Supply Voltage: 1.8 V to 5.25 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F560DK
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1691 - KIT DEVELOPMENT FOR C8051F560
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1700

1. Clear RI0 to 0.
2. Read SBUF0.
3. Check RI0, and repeat at step 1 if RI0 is set to 1.
If the extra bit function is enabled (XBE0 = 1) and the parity function is disabled (PE0 = 0), the extra bit for
the oldest byte in the FIFO can be read from the RBX0 bit (SCON0.2). If the extra bit function is not
enabled, the value of the stop bit for the oldest FIFO byte will be presented in RBX0. When the parity func-
tion is enabled (PE0 = 1), hardware will check the received parity bit against the selected parity type
(selected with S0PT[1:0]) when receiving data. If a byte with parity error is received, the PERR0 flag will be
set to 1. This flag must be cleared by software. Note: when parity is enabled, the extra bit function is not
available.
23.3.3. Multiprocessor Communications
UART0 supports multiprocessor communication between a master processor and one or more slave pro-
cessors by special use of the extra data bit. When a master processor wants to transmit to one or more
slaves, it first sends an address byte to select the target(s). An address byte differs from a data byte in that
its extra bit is logic 1; in a data byte, the extra bit is always set to logic 0.
Setting the MCE0 bit (SMOD0.7) of a slave processor configures its UART such that when a stop bit is
received, the UART will generate an interrupt only if the extra bit is logic 1 (RBX0 = 1) signifying an
address byte has been received. In the UART interrupt handler, software will compare the received
address with the slave's own assigned address. If the addresses match, the slave will clear its MCE0 bit to
enable interrupts on the reception of the following data byte(s). Slaves that weren't addressed leave their
MCE0 bits set and do not generate interrupts on the reception of the following data bytes, thereby ignoring
the data. Once the entire message is received, the addressed slave resets its MCE0 bit to ignore all trans-
missions until it receives the next address byte.
Multiple addresses can be assigned to a single slave and/or a single address can be assigned to multiple
slaves, thereby enabling "broadcast" transmissions to more than one slave simultaneously. The master
processor can be configured to receive all transmissions or a protocol can be implemented such that the
master/slave role is temporarily reversed to enable half-duplex transmission between the original master
and slave(s).
RX
Master
Device
Figure 23.6. UART Multi-Processor Mode Interconnect Diagram
TX
RX
Device
Slave
TX
Rev. 1.1
RX
Device
Slave
TX
C8051F55x/56x/57x
RX
Device
Slave
TX
V+
237