PIC32MX440F512H-80I/PT Microchip Technology, PIC32MX440F512H-80I/PT Datasheet - Page 17

• Manufacturer Part Number: PIC32MX440F512H-80I/PT
• Description: IC PIC MCU FLASH 512K 64-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 32MXr

Specifications of PIC32MX440F512H-80I/PT

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 64-TFQFP
• Core Processor: MIPS32® M4K™
• Core Size: 32-Bit
• Speed: 80MHz
• Connectivity: I²C, IrDA, LIN, PMP, SPI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 53
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.3 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC32MX4xx
• Core: MIPS
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: I2C , SPI , UART
• Maximum Clock Frequency: 80 MHz
• Number Of Programmable I/os: 51
• Number Of Timers: 5 x 16 bit, 1 x 32 bit
• Operating Supply Voltage: 2.3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, DM320003, DM320002, MA320002
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Controller Family/series: PIC32
• No. Of I/o's: 51
• Ram Memory Size: 32KB
• Cpu Speed: 80MHz
• No. Of Timers: 5
• Embedded Interface Type: EUART, I2C, PSP, SPI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC244003 - TEST BD MPLAB REAL ICE LOOPBACKDM320003 - BOARD DEMO USB PIC32 OTGAC244006 - KIT MPLAB REAL ICE TRACEAC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

© 2009 Microchip Technology Inc.
2.4.2
Perform the following steps to view the tutorial:
1. After your computer has rebooted, the Getting Started Tutorial menu opens.
2. View the tutorial instructions for connecting to the starter kit board and running
If you performed the installation steps as you followed along in the Getting Started
tutorial, skip to Section 2.5 “Starting the Tutorial Project” on page 16.
If you did not, continue to the next page for instructions about how to connect the board
and install the device driver.
2.4.3
Using the supplied USB cable, connect the board to an open USB port on your com-
puter. (A USB hub that is not bus-powered can also be used.) Connect the other end
of the cable into the USB connector on the starter kit board.
Check the board: the green power LED D3 should be lit. If it is not, check the
connections at the port, hub, and board.
2.4.4
Perform the following steps to install the USB device driver:
1. When the USB cable is connected, the “Found New Hardware Wizard” dialog
FIGURE 2-2:
Note:
the tutorial project.
box opens, as shown in Figure 2-2. When asked whether to install the software
automatically or install from a list or specific location, select “Install software
automatically” and click Next.
View the Getting Started Tutorial
Connect the Starter Kit Board
Install the USB Device Driver
The USB driver installation steps described here refer specifically to
installing the driver on a Microsoft Windows XP operating system.
FOUND NEW HARDWARE WIZARD
DS61144D-page 13