PIC18LF4620-I/ML Microchip Technology, PIC18LF4620-I/ML Datasheet - Page 2

• Manufacturer Part Number: PIC18LF4620-I/ML
• Description: IC MCU FLASH 32KX16 44QFN
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF4620-I/ML

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFN
• Controller Family/series: PIC18
• No. Of I/o's: 36
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 3.875KB
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Processor Series: PIC18LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3986 B
• Interface Type: SPI, I2C, EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 1 x 8
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM163022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18F2525/2620/4525/4620
2. Module: MSSP
3. Module: MSSP
DS80224E-page 2
After an I
register may be written for up to 10 T
additional writes are blocked. The data transfer may
be corrupted if SSPBUF is written during this time.
The WCOL bit is set any time an SSPBUF write
occurs during a transfer.
Work around
Avoid writing SSPBUF until the data transfer is
complete, indicated by the setting of the SSPIF bit
(PIR1<3>).
Verify the WCOL bit (SSPCON1<7>) is clear after
writing SSPBUF to ensure any potential transfer in
progress is not corrupted.
Date Codes that pertain to this issue:
All engineering and production devices.
In 10-Bit Addressing mode, when a Repeated Start
is issued followed by the high address byte and a
write command (R/W = 0), an ACK is not issued.
Work around
There are two work arounds available:
1. Single Master Environment:
In a single master environment, the user must
issue a Stop, then a Start followed by a write to the
address high, then the address low followed by the
data.
2. Multi-Master Environment:
In a multi-master environment, the user must issue
a Repeated Start, send a dummy write command
to a different address, issue another Repeated
Start and then send a write to the original address.
This procedure will help maintain control of the
bus.
Date Codes that pertain to this issue:
All engineering and production devices.
2
C transfer is initiated, the SSPBUF
CY
before
4. Module: MSSP
5. Module: ECCP
I
bit should be set) only when the system is idle
(i.e., when ACKEN, RCEN, PEN, RSEN and SEN
all equal zero). It should not be possible to set the
RCEN bit when the system is not idle, however,
the RCEN bit can be set under this circumstance.
Work around
Wait for the system to become idle before setting the
RCEN bit. This requires a check for the following bits
to be clear:
ACKEN, RCEN, PEN, RSEN and SEN.
Date Codes that pertain to this issue:
All engineering and production devices.
When the CCP1 auto-shutdown feature is
configured for automatic restart by setting the
PRSEN bit (PWM1CON<7>), the pulse terminates
immediately in a shutdown event. In addition, the
pulse may restart within the period if the shutdown
condition expires. This may result in the generation
of short pulses on the PWM output(s).
Work around
Configure the auto-shutdown for software restart
by clearing the PRSEN bit (PWM1CON<7>). The
PWM can be re-enabled by clearing the
ECCPASE bit (ECCP1AS<7>) after the shutdown
condition expires.
Date Codes that pertain to this issue:
All engineering and production devices.
2
C Receive mode should be enabled (i.e., RCEN
© 2008 Microchip Technology Inc.