PIC18F4553-I/P Microchip Technology, PIC18F4553-I/P Datasheet - Page 21

• Manufacturer Part Number: PIC18F4553-I/P
• Description: IC PIC MCU FLASH 16KX16 40-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4553-I/P

• Program Memory Type: FLASH
• Program Memory Size: 32KB (16K x 16)
• Package / Case: 40-DIP (0.600", 15.24mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 34
• Eeprom Size: 256 x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 13x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: MSSP/I2C/SPI/EUSART/CCP/ECCP
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM163025
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM163025 - PIC DEM FULL SPEED USB DEMO BRD444-1001 - DEMO BOARD FOR PICMICRO MCU
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

2.0
The Analog-to-Digital (A/D) Converter module has
10 inputs for the 28-pin devices and 13 for the 40-pin
and 44-pin devices. This module allows conversion of an
analog input signal to a corresponding 12-bit digital
number.
The module has five registers:
• A/D Result High Register (ADRESH)
• A/D Result Low Register (ADRESL)
• A/D Control Register 0 (ADCON0)
• A/D Control Register 1 (ADCON1)
• A/D Control Register 2 (ADCON2)
REGISTER 2-1:
© 2009 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7-6
bit 5-2
bit 1
bit 0
Note 1:
U-0
—
2:
12-BIT ANALOG-TO-DIGITAL
CONVERTER (A/D) MODULE
These channels are not implemented on 28-pin devices.
Performing a conversion on unimplemented channels will return a floating input measurement.
Unimplemented: Read as ‘0’
CHS3:CHS0: Analog Channel Select bits
0000 = Channel 0 (AN0)
0001 = Channel 1 (AN1)
0010 = Channel 2 (AN2)
0011 = Channel 3 (AN3)
0100 = Channel 4 (AN4)
0101 = Channel 5 (AN5)
0110 = Channel 6 (AN6)
0111 = Channel 7 (AN7)
1000 = Channel 8 (AN8)
1001 = Channel 9 (AN9)
1010 = Channel 10 (AN10)
1011 = Channel 11 (AN11)
1100 = Channel 12 (AN12
1101 = Unimplemented
1110 = Unimplemented
1111 = Unimplemented
GO/DONE: A/D Conversion Status bit
When ADON = 1:
1 = A/D conversion in progress
0 = A/D Idle
ADON: A/D On bit
1 = A/D Converter module is enabled
0 = A/D Converter module is disabled
U-0
—
ADCON0: A/D CONTROL REGISTER 0
W = Writable bit
‘1’ = Bit is set
R/W-0
CHS3
(2)
(2)
(2)
(1,2)
(1,2)
(1,2)
PIC18F2458/2553/4458/4553
R/W-0
CHS2
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-0
CHS1
The ADCON0 register, shown in Register 2-1, controls
the operation of the A/D module. The ADCON1
register, shown in Register 2-2, configures the
functions of the port pins. The ADCON2 register,
shown in Register 2-3, configures the A/D clock
source, programmed acquisition time and justification.
R/W-0
CHS0
x = Bit is unknown
GO/DONE
R/W-0
DS39887C-page 21
R/W-0
ADON
bit 0