PIC18F4321-I/PT Microchip Technology, PIC18F4321-I/PT Datasheet - Page 169

• Manufacturer Part Number: PIC18F4321-I/PT
• Description: IC PIC MCU FLASH 4KX16 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4321-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 8KB (4K x 16)
• Package / Case: 44-TQFP, 44-VQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: EUSART/I2C/MSSP/SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT44PT3 - SOCKET TRAN ICE 44MQFP/TQFPAC164305 - MODULE SKT FOR PM3 44TQFP444-1001 - DEMO BOARD FOR PICMICRO MCUAC164020 - MODULE SKT PROMATEII 44TQFP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

REGISTER 18-2:
© 2009 Microchip Technology Inc.
bit 7
bit 6
bit 5
bit 4
bit 3-0 SSPM<3:0>: Synchronous Serial Port Mode Select bits
SSPCON1: MSSP CONTROL REGISTER 1 (SPI MODE)
PIC18F2221/2321/4221/4321 FAMILY
bit 7
WCOL: Write Collision Detect bit (Transmit mode only)
1 = The SSPBUF register is written while it is still transmitting the previous word
0 = No collision
SSPOV: Receive Overflow Indicator bit
SPI Slave mode:
1 = A new byte is received while the SSPBUF register is still holding the previous data. In case
0 = No overflow
SSPEN: Synchronous Serial Port Enable bit
1 = Enables serial port and configures SCK, SDO, SDI and SS as serial port pins
0 = Disables serial port and configures these pins as I/O port pins
CKP: Clock Polarity Select bit
1 = Idle state for clock is a high level
0 = Idle state for clock is a low level
0101 = SPI Slave mode, clock = SCK pin, SS pin control disabled, SS can be used as I/O pin
0100 = SPI Slave mode, clock = SCK pin, SS pin control enabled
0011 = SPI Master mode, clock = TMR2 output/2
0010 = SPI Master mode, clock = F
0001 = SPI Master mode, clock = F
0000 = SPI Master mode, clock = F
Legend:
R = Readable bit
-n = Value at POR
WCOL
R/W-0
Note:
Note:
Note:
(must be cleared in software)
of overflow, the data in SSPSR is lost. Overflow can only occur in Slave mode. The user
must read the SSPBUF, even if only transmitting data, to avoid setting overflow (must be
cleared in software).
In Master mode, the overflow bit is not set since each new reception (and
transmission) is initiated by writing to the SSPBUF register.
When enabled, these pins must be properly configured as input or output.
Bit combinations not specifically listed here are either reserved or implemented in
I
2
C™ mode only.
SSPOV
R/W-0
W = Writable bit
‘1’ = Bit is set
SSPEN
R/W-0
OSC
OSC
OSC
R/W-0
CKP
/64
/16
/4
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
SSPM3
R/W-0
SSPM2
R/W-0
x = Bit is unknown
SSPM1
R/W-0
DS39689F-page 169
SSPM0
R/W-0
bit 0