PIC18F26K20-I/SS Microchip Technology, PIC18F26K20-I/SS Datasheet - Page 26

• Manufacturer Part Number: PIC18F26K20-I/SS
• Description: IC PIC MCU FLASH 32KX16 28-SSOP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F26K20-I/SS

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Core Processor: PIC
• Speed: 64MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SSOP
• Controller Family/series: PIC18
• No. Of I/o's: 25
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 3.84375KB
• Cpu Speed: 64MHz
• No. Of Timers: 4
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3936 B
• Interface Type: CCP, ECCP, EUSART, I2C, MSSP, SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 11 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164112 - VOLTAGE LIMITER MPLAB ICD2 VPPAC164307 - MODULE SKT FOR PM3 28SSOP
• Lead Free Status / Rohs Status: Details

PIC18F2XK20/4XK20
4.3
A configuration address may be read and output on
PGD via the 4-bit command, ‘1001’. Configuration data
is read and written in a byte-wise fashion, so it is not
necessary to merge two bytes into a word prior to a
compare. The result may then be immediately
compared to the appropriate configuration data in the
programmer’s memory for verification. Refer to
Section 4.1 “Read Code Memory, ID Locations and
Configuration Bits” for implementation details of
reading configuration data.
4.4
Data EEPROM is accessed one byte at a time via an
Address Pointer (register pair EEADRH:EEADR) and a
data latch (EEDATA). Data EEPROM is read by loading
EEADRH:EEADR with the desired memory location
and initiating a memory read by appropriately configur-
ing the EECON1 register. The data will be loaded into
EEDATA, where it may be serially output on PGD via
the 4-bit command, ‘0010’ (Shift Out Data Holding
register). A delay of P6 must be introduced after the
falling edge of the 8th PGC of the operand to allow
PGD to transition from an input to an output. During this
time, PGC must be held low (see Figure 4-4).
The command sequence to read a single byte of data
is shown in Table 4-2.
TABLE 4-2:
DS41297F-page 26
Step 1: Direct access to data EEPROM.
Step 2: Set the data EEPROM Address Pointer.
Step 3: Initiate a memory read.
Step 4: Load data into the Serial Data Holding register.
Note 1:
Command
4-bit
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0010
Verify Configuration Bits
Read Data EEPROM Memory
The <LSB> is undefined. The <MSB> is the data.
READ DATA EEPROM MEMORY
Data Payload
<MSB><LSB>
OE <AddrH>
0E <Addr>
9E A6
9C A6
6E A9
6E AA
80 A6
50 A8
6E F5
00 00
BCF EECON1, EEPGD
BCF EECON1, CFGS
MOVLW <Addr>
MOVWF EEADR
MOVLW <AddrH>
MOVWF EEADRH
BSF EECON1, RD
MOVF EEDATA, W, 0
MOVWF TABLAT
NOP
Shift Out Data
Advance Information
(1)
FIGURE 4-3:
Core Instruction
No
Move to TABLAT
READ DATA EEPROM
FLOW
Shift Out Data
© 2009 Microchip Technology Inc.
Address
done?
Read
Byte
Start
Done
Set
Yes